Main Section; Mon, Aux Sends 1-4 Controls; Aux Send Jacks; Stereo Aux Return Connectors - Omnitronic LMC-1422FX Bedienungsanleitung

Operating Elements and Connections

Main section

MON, AUX SENDS 1-4 controls

LMC-2642FX
Fig. 4.7 Aux Send controls in the main section
Turning up the AUX 1 control in a channel routes the
signal to the aux send bus 1.
AUX SEND 1, 2 and 4 controls
The AUX SEND 1 control determines the master send
level of the mix created by the individual channel AUX 1
sends. Likewise, the AUX SEND 2 control is the master
control for the aux 2 bus, and AUX SEND 4 controls the
AUX 4 bus.
AUX SEND/DSP control
This control determines the signal level for effects
processing, i.e. regulates the level to the internal effect
processor or an external effects device connected to
output AUX SEND 3/FX (model LMC-2642FX). On
consoles LMC-1422FX and LMC-2022FX, this function
is performed by the AUX SEND 2 control.
SOLO switch
You can use the SOLO switch to separately monitor the
aux sends via the CONTROL ROOM/PHONES outputs
and check these with the level meters.

AUX SEND jacks

LMC-2642FX
Fig. 4.8 Aux send jacks
The unbalanced AUX SEND jacks should be used when
hooking up a monitor power amp or active monitor
speaker system. The relevant aux path should be set
pre-fader. As already mentioned, the aux sends in the
channels‒if set post-fader‒can be used to connect to
external effects devices.
Aux 4 is taken pre-fader and thus, can be used for
monitoring only.
AUX SEND 3/FX jack
The AUX SEND (FX) jack carries the master aux mix
(from the channel's FX controls). You can connect this to
an external effects device to process the FX bus. The
processed signal can then be brought from the effects
device back into the STEREO AUX RETURN jacks.

STEREO AUX RETURN connectors

LMC-2022FX
Fig. 4.9 Aux return connectors
The STEREO AUX RETURN 1 jacks generally serve as
the return for the effects mix (created using the post-
fader aux sends) by connecting the output of an external
effects device. If only the left jack is connected, the AUX
RETURN is automatically switched to mono. You can
also use these jacks as additional line inputs. All stereo
aux returns are balanced, but can of course also be
used with unbalanced connectors. If you use an aux
send for monitoring, the associated unused stereo aux
returns are available for other line level signals (e.g.
keyboards).
STEREO AUX RETURN 3/FX connectors
The STEREO AUX RETURN FX jacks accept the effects
mix return (created using the channel DSP sends). If
these jacks are already in use as additional inputs, you
can route the effects signal back into the console via a
different channel. The advantage of this is that you can
now use that channel's EQ on the effects return signal.
In this instance, the FX control of the channel
Notes
being used as an effects return should be turned fully
counterclockwise, otherwise feedback problems could
occur.
If you wish to use the internal effects processor, do not
plug any connectors into the STEREO AUX RETURN
FX jacks, unless you want to tap the processed signal
via the FX OUT (model LMC-2642FX).

Monitor section (model LMC-2022FX)

LMC-2022FX
Fig. 4.10 Monitor output
MON SEND output
The first aux send (MON) on the LMC-2022FX console
is used to set up the monitor mix from the channels and
route it to the MON SEND fader.
32
LMC-2642FX