Product Description And Specifications; Technical Data; Noise/Vibration Information - Bosch GBH 5-40 DCE Professional Originalbetriebsanleitung

OBJ_BUCH-1742-002.book Page 12 Wednesday, December 5, 2012 2:46 PM
12 | English
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause hear-
ing loss.
 Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for hammer drilling in concrete,
brick and stone as well as for chiselling.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Dust protection cap
2 Locking sleeve
1 609 92A 046 | (5.12.12)
3 Mode selector switch
4 Vibration damper
5 On/Off switch
6 Handle (insulated gripping surface)
7 Thumbwheel for speed preselection/impact frequency
preselection
8 Service indicator
9 Stand-by indicator
10 Auxiliary handle (insulated gripping surface)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Technical Data

Rotary Hammer
Article number
Rated power input
Speed
Impact rate
– Drilling mode
– Chiselling mode
Impact energy per stroke ac-
cording to EPTA-Procedure
05/2009
Chisel positions
Tool holder
Lubrication
Max. drilling dia.
– Concrete (with twist drill)
– Concrete (with break-through
drill bit)
– Brickwork (with core bit)
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
Hammer drilling into concrete: a = 10.5 m/s
h
2
Chiselling: a = 7.5 m/s , K= 1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
GBH 5-40 DCE
3 611 B64 0..
W 1150
-1
min 170 – 340
-1
min 1500 –2900
-1
min 1500 –3050
J 8.8
12
SDS-max
Central permanent
lubrication
mm 40
mm 55
mm 90
kg 6.8
/II
2 2
, K= 4.4 m/s ,
2
.
Bosch Power Tools