DeWalt DWV905M Übersetzung Der Originalanleitung Seite 29

3. If the alarm still continues to sound, remove hose and check
that it is clear. Remove and replace dust bag if full or blocked
and check filter condition and replace where necessary.
If the alarm continues to sound contact your local D
service agent.
Connecting to Power Tools (Fig. C, E)

WARNING: Only use the outlet for purposes specified in
the instructions.

WARNING: Before setting the switch to position "Tool
Control", make sure that the connected tool is switched off.

WARNING: The maximum load of the power tool shall
not exceed the rated maximum outlet power rating at the
socket outlet.
nOTE: Some Brushless AC tools can start the Vacuum in auto
mode without turning on the power tool.
1. Plug the vacuum power cord into an appropriate outlet.
2. Plug the power tool into the outlet
nOTE: See Power connection data of power tool under
Technical Data for the power allowance of the tool to be
plugged into the outlet.
3. Turn on/off/tool control switch
position . This allows the vacuum to be turned on and
off automatically by the power tool. The minimum power of
the tool must be larger than 250 watts for the Vacuum to be
controlled via the socket?
nOTE: The vacuum cleaner starts automatically within 0.5
seconds and continues to run for 7 seconds after the power
tool has been turned off. Afterrun can vary when used with
a power generator.
4. To switch back to manual mode, turn the on/off tool control
switch 15 to the ON position
and the vacuum are turned on and off independent of
each other.
5. Your D WALT construction dust extractor is fitted with the
e
D WALT AirLock connection system. The AirLock allows for
e
a fast, secure connection between the suction hose
power tool. The AirLock connector
D WALT compatable tools or through the use of an AirLock
e
adapter (available from your local D
to the Accessories section for detail on available adapters.
nOTE: If using an adapter ensure it is firmly attached to the
tool outlet before following the steps below.
a. Ensure the collar on the AirLock connector is in the
unlock position. Align notches
connector as shown for unlock and lock positions.
b. Push the AirLock connector onto the adapter
connector point.
c. Rotate the collar to the locked position.
nOTE: The ball bearings inside collar lock into slot and
secure the connection.The power tool is now securely
connected to the dust extractor.
Automatic Filter Cleaning System
This vacuum has a highly effective filter cleaning system which
minimizes filter clogging. Every 30 seconds, one of the two filters
WALT
e
13 .
15 to the ACTIVATION
). In manual mode the tool
7 and
24 connects directly to
WALT supplier). Refer
e
25 on collar and AirLock
gets automatically cleaned. The cleaning process alternates
between the filters and continues through the life of the unit.
nOTE: After starting the vacuum, both filters get cleaned within
the first 15 seconds.
nOTE: It is normal to hear a clicking sound during this process.
nOTE: After many hours of operation the automatic filter
cleaning system may not be effective. When this happens, see
clause Filter under Maintenance.
Parking Brake (Fig. F)
The parking brake will lock one wheel in place to prevent
vacuum from rolling.
1. To engage parking brake, depress the brake
brake into the locked position.
2. To disengage parking brake, depress the brake button and
brake will snap into the unlocked position.
Insert Dust Collection Bag (Fig. B)
When you insert the plastic bag, make sure you remove the air
between the tank and the bag as much as possible. Try to avoid
large wrinkles in the sealing between the head and the tank.
Remove / Change Used Dust Collection Bag

WARNING: Appropriate personal protective equipment
like dust mask and gloves should be used while handling
used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. To remove the suction hose, close the twist-lock hose
inlet 10 with the inlet plug
3. Unlatch canister latches
4. Pull the collection bag carefully from inlet.
5. Seal the collection bag opening tightly with adhesive
tape or a cable tie (not included) when removing it from
the machine.
6. Dispose of collection bag in appropriate container according
to statutory provisions.
Wet Pick Up Applications (Fig. G)

WARNING: DO NOT connect power tools to outlet
when using the vacuum for wet pick up.

WARNING: Plug vacuum into residual current device
(RCD) protected outlet when using the vacuum for wet
pick up.

WARNING: If foam or liquid escapes from the machine,
switch off immediately.

CAUTION: Clean the water level limiting device regularly
and examine it for signs of damage.
NOTICE: DO NOT remove ball float
cause damage to the vacuum. The ball float keeps water
from entering the motor.
Before using the vacuum for wet pick up:
1. Turn off vacuum and unlug power cord
2. Unlatch canister latches
3. Remove the dust bag
Dust collection Bag section).
26
19 .
4 and remove vacuum head
27
, doing so will
2 from outlet.
4 and remove the vacuum head.
(see the Remove / change Used
20
EnGLIsH
to snap the
3
13
27