Mounting And Wiring - Steute Rf Rx Sw868-1W 24Vac/Dc Montage- Und Anschlussanleitung

RF Rx SW868/SW915/SW917/SW922-1W 24VAC/DC
//
Montage- und Anschlussanleitung / Funk-Empfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
Istruzioni di montaggio e collegamento / Ricevitore wireless
Instruções de montagem e instalação / Receptor sem fio
Инструкция по монтажу и подключению / Радио-приемник
English
Use of the mounting and wiring instructions
Target group: authorised and qualified staff.
All actions described in these instructions may only be performed by
qualified persons who have been trained and authorised by the
operating company.
1. Read and understand these mounting and wiring instructions.
2. Comply with the valid occupational safety and accident prevention
regulations.
3. Install and operate the device.
Selection and installation of devices and their integration in control
systems demand qualified knowledge of all the relevant laws, as well
as the normative requirements of the machine manufacturer. In case
of doubt, the German language version of these instructions shall
prevail.
Scope of delivery
Device, mounting and wiring instructions, carton.
Intended use
The one channel radio receiver is used to switch electrical loads via
radio transmission. The transmitters must support the steute
Wireless protocol.

Mounting and wiring

The wireless range depends heavily on the local conditions. Conductive
materials may strongly affect the radio signal. This also includes thin
foils, e.g. aluminium laminations on insulation materials.
Antenna
Use suitable antennas only:
Device Antenna
RF magnet antenna 5dBi
SMA plug-in connector
straight 1.5 m
SW868/922
RF magnet antenna 2dBi
SMA plug-in connector
straight 2 m
RF magnet antenna 5dBi
R-SMA plug-in connector
straight 3.6 m
SW915/917
RF magnet antenna 2dBi
R-SMA plug-in connector
straight 2 m
Mount the antenna on a metal plate. The metal plate serves as HF
counterweight. Minimum size of metal plate: 250 x 250 mm. Observe
minimum sideways distance to nearest wall or disturbance source:
300 mm. Do not bend or clamp the cable. Minimum bending range of
cable: >15 mm.
Assignment of locations and radio frequencies:
Device type Radio frequency
SW868
SW915
SW917
SW922
Design of wireless range
The radio signal is attenuated on the way from the transmitter to the
receiver. In addition, the radio signal is influenced by obstacles. The
degree of attenuation depends on the material of the obstacle. The fol-
lowing tables serve as a guide.
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Location
in free field (SW868/915/917 LR)
in free field (SW868/915/917 ULR)
in free field (SW922 LR)
in free field (SW922 ULR)
Mat. No.
indoors (SW868/915/917 LR)
1188958
indoors (SW868/915/917 ULR)
indoors (SW922 LR)
1470770 indoors (SW922 ULR)
To get the maximum range: use the specified antennas. With other an-
tennas, the maximum range may differ.
1188987
Safety
Do not use the device in connection with other devices whose direct or
1470773
indirect purpose is to ensure life or health, or whose operation may
pose a threat to humans, animals or material assets.
N.B.
Subject to technical modifications. Reconstruction and alterations to
the device are not allowed. The described products were developed in
order to assume safety functions as part of an entire plant or machine.
It is the responsibility of the manufacturer of a plant or machine to
guarantee the correct general function.
3 / 20
Location
868.3 MHz EU
915.0 MHz USA
Canada
Mexico
917.0 MHz Brazil
916.5 MHz Japan
Penetration
90...100 %
65...95 %
10...90 %
0...10 %
Wireless range (approx.)
450 m
700 m
150 m
230 m
40 m
50 m
20 m
25 m
According to
2014/53/EU (RED)
FCC
IC
IFT
ANATEL
ARIB STD-T108