Ferm MSM1033 Originalbetriebsanleitung Seite 9

You can install the machine in two ways:
a. As a stationary machine on a workbench. In
this case the machine must be secured to the
workbench with 4 bolts.
b. As a stationary machine on the subframe. In
this case the machine must be secured to the
subframe with 4 bolts and the subframe
anchored to the floor or to a floor plate with
dimensions of at least 1 square meter.
Figs. 1 to 4
Make sure that the plug is not in the
socket when assembling and mounting
accessories.
Placement of the machine
Use screws to fix the machine to a sturdy
workbench.
• Place the machine on the workbench and
draw the positions of the holes on the
workbench.
• Drill holes in the marked places of the correct
diameter for the screws to be used.
• Put the machine on the workbench, place the
screws in the mounting holes (11) and screw
the screws tight.
Guide fence insert
For safety reasons, this machine is equipped with
a guide fence insert
to be used when using the machine for sawing
straight cross-cuts.
• For sawing straight cross-cuts, the guide
fence insert must remain mounted on the
machine (fig. 6).
• For sawing mitre cuts, the guide fence insert
must be removed from the machine as shown
(fig. 6).
• For sawing bevel cuts, the guide fence insert
must be removed from the machine as shown
(fig. 7+8).
Mounting the dust bag
In connection with the danger to health by
breathing in any dust released, you must mount
the dust bag (30) on the dust bag connection (5).
This also keeps the workplace cleaner longer.
• Press the clamp of the dust bag and slide it
over the outlet at the rear of the machine. Let
go of the clamp and the dust bag is then fixed
Ferm
in place.
Parallel and mitre guide (table saw)
Fig. 5
The guide is used to guide the piece of work along
the saw blade. The guide can be mounted to the
left and to the front of the saw blade.
• Slide the guide (17) with the holder into the
guide rail of the bench surface.
• Unscrew the setting screw on the degree arc
(25).
• Move the guide in the rail to the required
place.
• Set the desired angle with the aid of the
degree arc (25):
• parallel sawing: adjusting the guide parallel to
the saw blade
• mitring: setting the guide to the desired angle
in relation to the saw blade
• Screw the setting screw tight again.
• With the aid of the clamp screws (26) the
guide can be moved lengthwise.
Use of the machine:
Mitre saw or table saw
This combined machine can be used in two ways:
mitre saw or table saw. After use the machine
must always be left set up as the table saw.
Set-up for use as a mitre saw
1. Unscrew the screw (4) that locks the upper
bench surface.
2. Keep the saw head pushed downwards
against the handgrip (2), while you bring the
upper bench surface (18) upwards.
3. Screw the screw (4) tight again.
4. Hold the saw head down with your left hand
and pull the lock (8) out with your right hand.
5. Gently let the saw head come upwards.
6. Remove the lower protective hood (16).
7. Put the plug into the socket and test the saw
by pressing the switch (1).
Set-up as a table saw
1. Place the lower protective hood (16) on the
lower bench surface (12) of the cross-cut saw.
2. Hold the operating handgrip (2) firmly with
your right hand. Press the locking knob (3)
with your thumb and bring the saw head
downwards. The saw blade is then completely
protected by the lower protective hood.
3. Lock the lock (8) in place.
4. Unscrew the screw (4) two turns.
5. Push the upper bench surface gently
EN
9