Overload Protection; Maintenance And Care - Flex CSM 4060 Bedienungsanleitung

Portable circular saw for metals CSM 4060
 Tighten the clamping lever (10).
Operation
`~ìíáçå>
Ó ^ÑíÉê=íÜÉ=éçïÉê=íççä=Ü~ë=ÄÉÉå=ëïáíÅÜÉÇ=çÑÑI=
íÜÉ=ë~ï=Ää~ÇÉ=ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
Ó tÜÉå=íÜÉ=êìååáåÖ=ë~ï=Ää~ÇÉ=íçìÅÜÉë=íÜÉ=
ïçêâéáÉÅÉI=íÜÉ=éçïÉê=íççä=ã~ó=êÉÅçáäK
Sawing
kçíÉ>
bñÅÉëëáîÉ=ÑÉÉÇ=êÉÇìÅÉë=íÜÉ=éÉêÑçêã~åÅÉ=çÑ íÜÉ=
éçïÉê=íççäI=áãé~áêë=íÜÉ=ÅìííáåÖ=èì~äáíó=~åÇ=
êÉÇìÅÉë=íÜÉ=ëÉêîáÅÉ=äáÑÉ=çÑ=íÜÉ=ë~ï=Ää~ÇÉK=
 Take hold of the handle (1) with your right
hand and the additional hand grip (6) with
your left hand.
 Switch on the power tool and wait until the
saw blade has reached the maximum
speed.
 Slowly bring the power tool towards
the material.
 Guide the power tool through the material
at a uniform feed.
Parallel stop
Facilitates cuts parallel to the edge of the
workpiece.
 Loosen the wing screw (8).
 Set the parallel stop (18) to the required
width.
 Tighten the wing screw (8).

Overload protection

If there is an extreme overload, the overload
protection system protects the motor from
damage by automatically switching off the
power tool.
 Release the safety switch (4).
 Pull out the mains plug.
 Leave the appliance to cool down for
at least 3 minutes.
 Press the overload protection reset
button (2).
The power tool is ready to use again.

Maintenance and care

a~åÖÉê>
_ÉÑçêÉ=Å~êêóáåÖ=çìí=~åó=ïçêâ=çå=íÜÉ=éçïÉê=
íççäI=~äï~óë=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
a~åÖÉê>
fãé~áêãÉåí=çÑ=íÜÉ=éêçíÉÅíáîÉ=áåëìä~íáçå>
fÑ=ãÉí~äë=~êÉ=ë~ïå=çîÉê=~ éêçäçåÖÉÇ=éÉêáçÇI=
ÅçåÇìÅíáîÉ=Çìëí=ã~ó=ÄÉÅçãÉ=ÇÉéçëáíÉÇ=áåëáÇÉ=
íÜÉ=ÜçìëáåÖK=
léÉê~íÉ=íÜÉ=éçïÉê=íççä=îá~=~ êÉëáÇì~äJÅìêêÉåíJ
çéÉê~íÉÇ=ÅáêÅìáíJÄêÉ~âÉê=EíêáééáåÖ ÅìêêÉåí=
PM ã^FK
 Regularly clean the power tool and
ventilation slots.
 Regularly blow out the housing interior and
motor with dry compressed air.
23