Operating Mode - Desoutter ERS2 Bedienungsanleitung

6159928100_02
Original instructions.
© Copyright 2022, Ets Georges Renault
44818 St Herblain, FR
All rights reserved. Any unauthorized use
or copying of the contents or part thereof
is prohibited. This applies in particular to
trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of
unauthorised parts is not covered by Warranty or
Product Liability.
STATEMENT OF USE
Tool (class I) suitable for industrial environment
only.
Usable with following controllers only :
● CVIRII, CVI3 ESSENTIAL*, CVI3 VISION*,
CVI3 FUNCTION*, CVI3 VISION-ESTOP*,
CVI3 FUNCTION-ESTOP*, TWINCVI3*,
TWINCVI3-ESTOP*.
(*) Use EMC filter 6159365370 when controllers
power supply voltage is equal or below 120V.
Intended use:
This product is intended to be used for installing
and removing threaded fasteners in wood, metal
or plastic.
No other user permitted.
For professional use only.
Regional requirements
WARNING
This product can expose you to chemicals
including lead, which is known to the
State of California to cause cancer
and birth defects or other reproductive
harm. For more information go to www.
P65Warnings.ca.gov
DATA
(See page 4).
Noise level: < 70 dB(A) (EN62841).
Vibration level: < 2.5 m/s².
Working temperature : 0 / +40°C.
Humidity ratio : 0 / 90%.
ERS tools are ESD (ElectroStatic
Discharge) certified screwdrivers,
according to requirements of IEC
EPA
61340-5-1 standard.
Declaration of noise and vibration emission
All values are current as of the date of this
publication. For the latest information please visit
desouttertools.com.
These declared values were obtained by
laboratory type testing in accordance with the
stated standards and are suitable for comparison
with the declared values of other tools tested
in accordance with the same standards. These
declared values are not adequate for use in risk
assessments and values measured in individual
work places may be higher. The actual exposure
values and risk of harm experienced by an
individual user are unique and depend upon
the way the user works, the workpiece and the
workstation design, as well upon the exposure
time and the physical condition of the user.
We, Desoutter, cannot be held liable for the
consequences of using the declared values,
instead of values reflecting the actual exposure,
in an individual risk assessment in a work place
situation over which we have no control.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
An EU guide to managing hand-arm vibration
can be found at http://www.pneurop.eu/uploads/
documents/pdf/PN3-02-NV_Declaration_info_
sheet_0111.pdf
We recommend a programme of health
surveillance to detect early symptoms which
may relate to noise or vibration exposure, so that
management procedures can be modified to help
prevent future impairment.

OPERATING MODE

The tool can be handheld or used as fixed
spindle on a tool.
Handheld tool
● Fit the tool with a suitable fastening
accessory, then connect it to the power supply
by means of the controller.
● Select the program and appropriate command
mode on the controller (for a PUSH START
operation: enable the PUSH START command
in the controller. To start in lever mode:
disable the PUSH START command).
● Hold the tool by means of the handle and
apply to the fastener to be tightened.
● In PUSH START mode (B), apply axial thrust
with the tool on the fastener to be tightened,
to start the tool.
● In lever mode (A), press the lever to start the
tool.
● For a reverse rotation (C), you can choose
between 2 functioning modes parametrisable
in the controller:
- Briefly press the inversion button, then
press either on PUSH START or on the
lever to start the tool. To return to the
screwing position, press again on the
inversion button.
- Briefly press the inversion button, then
press either on PUSH START or on the
lever to start the tool. At the next starting,
the tool automatically starts in the tightening
direction.
B
As the reaction force increases in proportion to
the tightening torque, make sure that the tool
is in perfect working order and the controller
is programmed correctly, to reduce the risk of
injury to the operator as a result of unexpected
behaviour of the tool.
10 / 78
English
A
C
05/2022