DeWalt DW743 Anweisungen Seite 33

● Check for damage to the tool, parts or accessories which may have
occurred during transport.
● Take the time to thoroughly read and understand this manual prior to
operation.
● Remove the saw from the packaging material carefully.
Description (fi g. A1 - A8)
Your DW743 fl ip-over sawing machine has been designed to operate
as a mitre saw or as a saw bench to perform the four main sawing
operations of ripping, cross-cutting, bevelling and mitring easily,
accurately and safely.
Mitre saw mode
In mitre saw mode, the sawing machine is used in vertical, mitre or
bevel position.
Saw bench mode
Turned over on its central axis, the sawing machine is used to perform
the standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.
Features
A1
1 On/off switch (saw bench mode)
2 Table release lever
3 Mitre saw table
4 Rotating table
5 Rotating table clamp
6 Fence right-hand side
7 Fence left-hand side
8 Rotating table location plunger
9 Mitre scale/table insert
10 Dust extraction adapter
11 Fixed upper blade guard
12 Moveable lower blade guard
13 Guard release lever
14 Operating handle
A2
14 Operating handle
15 Trigger switch (mitre saw mode)
16 Riving knife storage
17 Push stick storage
18 Leg
19 Foot
20 Table locking device
21 Saw table retention bracket
22 Bevel clamp handle
Saw bench mode
A3
22 Bevel clamp handle
23 Height adjuster
24 Saw bench table
25 Upper blade guard
26 Parallel fence
27 Mitre fence (option)
Optional accessories
For use in mitre saw mode:
A4
28 Adjustable stand 760 mm (max. height) (DE3474)
29 Support guide rails 1,000 mm (DE3494)
29 Support guide rails 500 mm (DE3491)
30 Swivelling stop (DE3462)
31 Length stop for short workpieces (to be used with guide rails [35])
(DE3460)
32 Support with removable stop (DE3495)
33 Support with stop removed (DE3495)
34 Material clamp (DE3461)
A5
35 Roller support table (DE3489)
For use in saw bench mode:
A3
27 Mitre fence (DE3496)
A6
36 Extension table (DE3472)
A7
37 Single sliding table (DE3471)
(not shown)
– Double sliding table
– Saw bench guard
For use in all modes:
A8
38 Three way dust extraction kit (DE3500)
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement
(U.K. & Ireland only)
● Should your mains plug need replacing and you are competent to
do this, proceed as instructed below. If you are in doubt, contact an
authorized D WALT repair agent or a qualifi ed electrician.
E
● Disconnect the plug from the supply.
● Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
● Only fi t 13 Amperes BS1363A approved plugs fi tted with the correctly
rated fuse (1).
● The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2), blue is for
Neutral (N) (4) and green/yellow is for Earth (E).
● Before replacing the top cover of the mains plug ensure that the
cable restraint (3) is holding the outer sheath of the cable fi rmly and
that the leads are correctly fi xed at the terminal screws.
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth
pin marked E or
E N G L I S H
.
33