Herunterladen Inhalt Inhalt Diese Seite drucken

Optional Accessories; Protecting The Environment; Rechargeable Battery Pack - DeWalt XR LI-ION DCS7485 Originalanweisungen

Kabellose tischkreissäge
Vorschau ausblenden Andere Handbücher für XR LI-ION DCS7485:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 25
Cleaning (Fig. A, R)

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean
the table top.

WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
The blade guard assembly 
 11 
in position before operating the saw.
Before use, carefully inspect upper and lower blade guards as
well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or work piece particles cannot
lead to blockage of one of the functions.
In case workpiece fragments are jammed between saw blade
and guards, disconnect the machine from the power supply
and follow the instructions given in section Mounting the
saw blade. Remove the jammed parts and reassemble the
saw blade.
Keep the ventilation slots clear and regularly clean the housing
with a soft cloth.
Regularly clean the dust collection system:
1. Turn the saw on its side, so the bottom, open part of the
unit is accessible.
2. Open the dust access door 
the two screws 
 48 
and detaching the door. Clean out
the excess dust, Then reattach the door securing it with
the screws.

Optional Accessories


WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Replace blade guard when worn. Contact your local D
service centre for details on a blade guard replacment.
saW BLaDEs: ALWAYS USE 210 mm noise reduced saw blades
with 30 mm arbour holes. Blade speed rating must be al least
6000 RPM. Never use a smaller diameter blade. It will not be
guarded properly.
and throat plate must be placed
shown in figure R loosening
 47 
WALT recommended
e
WALT
e
BLADE DESCRIPTIONS
application
construction saw Blades (fast rip)
General Purpose
Fine Crosscuts
Woodworking saw Blades
(provide smooth, clean cuts)
Fine crosscuts
Consult your dealer for further information on the
appropriate accessories.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
Run the battery pack down completely, then remove it from
the tool.
Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
EnGLIsh
Diameter
Teeth
210 mm
24
210 mm
40
210 mm
60
55

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dcs7485

Inhaltsverzeichnis