S&P CRHB 400 N ECOWATT PLUS Bedienungsanleitung Seite 16

Modbus Register
adress
30044 S_YEAR_ALARM_1
30045 S_MONTH_ALARM_1
30046 S_DAY_ALARM_1
30047 S_HOUR_ALARM_1
30048 S_MINUTES_ALARM_1
30049 S_SECONDS_ALARM_1
DE
30050 S_ALARM_2
30051 S_YEAR_ALARM_2
30052 S_MONTH_ALARM_2
30053 S_DAY_ALARM_2
30054 S_HOUR_ALARM_2
30055 S_MINUTES_ALARM_2
30056 S_SECONDS_ALARM_2
HOLDING REGISTERS (READ/WRITE)
Modbus Register
adress
Modbus configuration
40001 Adress
40002 Baud rate
40003 Parity
Resets
40004 Factory_Reset
40005 Reset_Alarms_Count
40006 Full_Reset
General configuration
40009 Vreg_Limit_min
40010 Vreg_Limit_max
40011 Taco_pulses_out
40012 Vreg_BOOST
40013 NIGHT_REDUCTION
40014 BOOST_TIMER
40017 SLAVE_ENABLE
40018 SLAVE_OFFSET
16
Data type Range
16 BITS 18 – 999
16 BITS 1 – 12
16 BITS 1 – 31
16 BITS 0 – 23
16 BITS 0 – 59
16 BITS 0 – 59
16 BITS 0 – 1
16 BITS 18 – 999
16 BITS 1 – 12
16 BITS 1 – 31
16 BITS 0 – 23
16 BITS 0 – 59
16 BITS 0 – 59
Data Range
type
CRHB/CRVB N
CRHT/CRVT N
ECOWATT PLUS
16 BITS 1 – 247
16 BITS 0 – 3
16 BITS 0 – 2
16 BITS 0 – 65535
16 BITS 0 – 65535
16 BITS 0 – 65535
16 BITS 0 – 10000
16 BITS 0 – 10000
16 BITS 0 – 10
16 BITS 0 – 10000
16 BITS 0 – 100
16 BITS 0 – 600
16 BITS 0 – 1
16 BITS -50 – 50
Description
Year of last IAQ alarm
Month of last IAQ alarm
Day of last IAQ alarm
Hour of last IAQ alarm
Minute of last IAQ alarm
Second of last IAQ alarm
Second to last IAQ alarm:
0: No alarm
1: AN1 IAQ alarm
2: AN2 IAQ alarm
3: AN3 IAQ alarm
Year of second to last IAQ alarm
Month of second to last IAQ alarm
Day of second to last IAQ alarm
Hour of second to last IAQ alarm
Minute of second to last IAQ alarm
Second of second to last IAQ alarm
Default Description
1 Modbus channel
Transmission speed
0: 4800bps
2 1: 9600bps
2: 19200bps
3: 38400bps
Transmission parity
0: EVEN
0 1: ODD
2: NONE
If parity NONE, 2 bits stop as default. If not, 1 bit stop
Back to factory settings
0
1234: Reset factory settings
Alarm count reset independently
0 2345: Motor alarm count
2456: IAQ alarm count
To reset all
0
3456: Full reset
1500 Minimum 0-10 voltage tension to the motor (mV)
10000 Maximum 0-10 voltage tension to the motor (mV)
1 Pulses by motor revolution
10000 Voltage in mV when Boost activated
% that will decrease the motor control voltage (VAV
50
mode) or setpoint (COP and CAV modes)
Time in minutes that boost will be activated once
0
disconnected
Slave function:
1 0: OFF
1: ON
Offset applied to slave in comparison with master
0 setpoint. Take into account control limits defined by
40009 and 40010