Intended Use; Safety Instructions; General Safety Instructions; Safety Instructions Operator - haacon ESG C1 Betriebsanleitung

– The following is not permitted:
– Exceeding the permissible load (see type, load plate and
technical data).
– Conveyance of passengers
– Persons standing under suspended loads.
– Pulling away jammed or blocked loads, dragging of loads
and pulling diagonally.
– Transporting burning liquid material.
– Working with defective winches, rope or load carrying equip-
ment.
– Working outside of the permissible temperature range.
– Operation in tropical environment.
Operating range:
– The winch corresponds to the EN 14492-1 "Power driven
winches" as well as the Accident Prevention Regulations
BGV D8 "Winches, hoists, and pulling equipment".
The equipment is not certified for
– Building elevators (BGV D7).
– Stages and studios (BGV C1).
– Conveying loads above lines and pipes, through which
combustible gases or liquids which could also be harmful to
health only with control units according to safety category 2.
– Lifting equipment for persons (ZH 1/461).
– Use in explosive environment (ATEX).
The device is unsuitable for
– Continuous operation (see technical data, motor group).
– Excessive inching operation.
– Use during constant vibration.
– Use on seagoing vessels and mobile offshore equipment.
– Aggressive environment.
– Forestry.
Limited suitability for (specific design):
– Stationary offshore equipment

2. SAfEtY inStruCtiOnS

2.1 General Safety instructions

The device corresponds to all relevant regulations. Never-
theless its use can endanger the user or third parties and/or
damage the device and other material assets in the case of:
– Not instructed (trained) personnel.
– Non-intended use.
– Inappropriate service/maintenance.
Certain residual risks are given even if all safety instructions
have been observed. Whoever works with or in the vicinity of
the device, must be familiar with these dangers and obey in-
structions, which prevent that residual risks result in accidents
or damages.
The residual risks are marked by symbols (explanation in
Chapter 1.1).
094319_a_de_gb_eseilwi_v haacon hebetechnik gmbh – Telefon +49 (0) 9375 - 84-0 – Fax +49 (0) 9375 - 84-66
Safety devices
Check the safety devices regularly for perfect function (--> also
Chapter 7 and 8):




1 Holding brake Always check before beginning work
2 Limit switch Required according to EN 14492-1; Adjust
before commissioning; Regular examination
3 Pressure roll Regular examination
4 Slack rope switch Adjust before commissioning; Regular
examination
5 Load limiting Required according to EN 14492-1 for loads
device, overload ≥ 1000 kg; Adjust before commissioning;
protection Regular examination
6 Motor shut-down Adjust before commissioning;
during Emergency Examination before use and according to
Hand Operation inspection plan

7 Motor shut-down with
detached drum
8 „Emergency stop"
switch
No. 2, 3, 4, 5 ,6 ,7 ,8 optional

2.2 Safety instructions Operator

The operator is obligated to plan and monitor all necessary
measures to guarantee safe operation.
The operator must ensure:
– The use is as intended (Chapter 1.4).
– The safety of the device is analysed according to its appli-
cation and environmental conditions and that recognizable
risks (e.g. danger of injury at rope inlet and rotating drum)
are assessed and eliminated.
– Before commissioning, the device has been examined and
approved according to the appropriate international and
national regulations.
– Operation is only carried out in a perfect, functional condition
– The safety devices are regularly examined for their effectiveness,
only ropes are used, which correspond to a valid standard and
are suitable for the application case. (Chapter 4.3)
– The required, personal protection equipment for the assem-
bly, operation, maintenance and repair personnel is available
and used.
– The operating manual must always be available at the device's
operational location in a legible and complete condition.
– Only qualified and authorised personnel may operate,
maintain, examined, and repair the device.The personnel
has been regularly instructed on all appropriate issues con-
cerning industrial safety and environmental protection, and
 

Adjust before commissioning; Regular
examination
Regular examination
GB
13