Machine Information; Technical Specifications - VONROC RS502AC Originalbetriebsanleitung

EN
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SAFETY WARNINGS FOR RECIPROCATING SAWS
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cut­
ting accessory may contact hidden wiring. Cut-
ting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
• Keep hands away from the sawing range. Do
not reach under the workpiece. Contact with
the saw blade can lead to injuries.
• Apply the machine to the workpiece only when
switched on. Otherwise there is danger of kick-
back when the cutting tool jams in the workpiece.
• When sawing, the base plate must always faces
against the workpiece. The saw blade can
become wedged and lead to loss of control over
the machine.
• When the cut is completed, switch off the
machine and then pull the saw blade out of the
cut only after it has come to a standstill. In this
manner you can avoid kickback and can place
down the machine securely.
• Use only undamaged saw blades that are in
perfect condition. Bent or dull saw blades can
break, negatively influence the cut, or lead to
kickback.
• Do not brake the saw blade to a stop by ap­
plying side pressure after switching off. The
saw blade can be damaged, break or cause
kickback.
• Clamp material well. Do not support the
workpiece with your hand or foot. Do not touch
objects or the floor with the the saw running.
Danger of kickback.
• Use appropriate detectors to determine if utility
lines are hidden in the work area or call the lo­
cal utility company for assistance. Contact with
electric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pen-
etrating a water line causes property damage.
• When working with the machine, always hold it
firmly with both hands and provide for a secure
6
stance. The power tool is guided more secure
with both hands.
• Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
• Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.

2. MACHINE INFORMATION

Intended use
The machine is intended for sawing wood, plastic and
metal while keeping the baseplate resting firmly on
the workpiece. It is suitable for straight and curved
cuts. It is also possible to cut flush to the workpiece
surface. A suitable saw blade must always be used.

TECHNICAL SPECIFICATIONS

Model No.
Voltage
Frequency
No load speed
Saw stroke
Max. saw capacity wood
Max. saw capacity steel
Weight
Sound pressure level L
PA
Sound power level L
WA
Vibration rear handle
Vibration front handle
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardized test given in EN60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
RS502AC
220-240V
50/60Hz
2600/min
20mm
115mm
5mm
2.74 kg
82.2 dB(A), K=3dB(A)
93.2 dB(A), K=3dB(A)
16.844 m/s K=1.5 m/s
2 2
18.067 m/s K=1.5 m/s
2 2
WWW.VONROC.COM