Replacing Lamps - Elica ILLUSION PRF0147727A Montage- Und Gebrauchsanweisungen

will activate for a limited period of time after which Speed 2 is
automatically enabled.
Remote control connection (if applicable)
Once the remote control has been connected, this will be displayed
on the hood:
both LEDs flash.
Note: Using the remote control, delayed shut-down can be
programmed based on the aspiration speed (power) enabled at that
moment:
Speed 1 (low aspiration): 20 minutes
Speed 2 (medium aspiration): 15 minutes
Speed 3 (high aspiration): 10 minutes
Filter Saturation indicator lights
At regular intervals, the LEDs on the hood indicate the need to carry
out filter maintenance.
Note: The filter saturation signal is visible for a few seconds when the
hood is switched on; within this time, the saturation indicator lights
must be reset.
Flashing Green LED: carry out maintenance on the grease filter.
Red flashing LED: carry out maintenance on the charcoal filter (only
for hoods operating in "Filtration Version").
Note: Run the "RESET FILTRES" command via the remote control.
Activating/deactivating the filter saturation indicator light
Note: Run the procedure with the hood switched off. The charcoal
filter saturation indicator light is usually deactivated.
If no control is given within maximum 10 sec, the hood automatically
exits this function, at any time, and returns to the previous state.
Press and hold the B+C keys (Simultaneously) to enter the setup
menu:
Briefly press button C to select the filter to be set up:
Grease filter:Green
Charcoal filter: Red
Briefly press button B to activate (the 2nd LED flashing) or deactivate
(2nd LED off).
Note: the LEDs light up for a limited number of seconds after which
they turn off to indicate that the indicator light has been activated (or
deactivated).
The device can also be used in combination with a Window
sensor KIT (not supplied by the manufacturer).
If the Window sensor KIT is installed (only in the case of use in
EXTRACTOR mode), air extraction will halt every time the window in
the room, on which the KIT is applied, is closed.
• The KIT must be electrically connected to the device by
qualified and specialised technical personnel.
• The KIT must be certified separately in accordance with the
safety standards for the component and its use with the device.
Installation must be carried out in accordance with current
regulations for domestic systems.
PLEASE NOTE:
• the wiring of the KIT to be connected to the device must be
part of a certified safety extra-low voltage (SELV) circuit.
• the manufacturer of this device declines all liability for any
inconvenience, damage or fires caused by defects and/or
problems associated with the malfunction and/or incorrect
installation of the KIT.
Maintenance
Cleaning
Clean using ONLY a cloth dampened with neutral liquid detergent.
DO NOT CLEAN WITH TOOLS OR INSTRUMENTS. Do not use
abrasive products. DO NOT USE ALCOHOL!
Panel
Fig. 3-17
The panel for perimeter suction should always be left closed and
should only be opened in case of maintenance interventions (eg
cleaning or replacing filters).
Grease filter
Fig. 3-17
Traps cooking grease particles.
This must be cleaned once a month (or when the filter saturation
indication system – if envisaged on the model in possession –
indicates this necessity) using non aggressive detergents, either by
hand or in the dishwasher, which must be set to a low temperature
and a short cycle.
When washed in a dishwasher, the grease filter may discolor slightly,
but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
It absorbs unpleasant odors caused by cooking.
The charcoal filter can be washed once every two months using hot
water and a suitable detergent, or in a dishwasher at 65°C (if the
dishwasher is used, select the full cycle function and leave dishes
out).
Eliminate excess water without damaging the filter, then remove the
mattress located inside the plastic frame and put it in the oven for 10
minutes at 100° C to dry completely. Replace the mattress every 3
years and when the cloth is damaged.

Replacing lamps

The hood is equipped with a lighting system based on LED
technology.
The LEDs guarantee an optimum lighting, a duration up to 10 times
longer than the traditional lamps and allow to save 90% electrical
energy.
The lighting system cannot be replaced by the user, contact
Customer Service in case of malfunction.
21