Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating- and Installation Instructions Hans Wilms GmbH & Co. KG
Operating- and Installation Instructions Hans Wilms GmbH & Co. KG
Operating- and Installation Instructions Hans Wilms GmbH & Co. KG
Gas Heaters Model Series GH 40 TH / GH 55 TH / GH 75 TH / GH 105 TH
Gas Heaters Model Series GH 40 TH / GH 55 TH / GH 75 TH / GH 105 TH
Gas Heaters Model Series GH 40 TH / GH 55 TH / GH 75 TH / GH 105 TH
Electric- and gas connection on the heater may be carried out only by a specialist
Electric- and gas connection on the heater may be carried out only by a specialist
according to the local directives! (In Germany i.e. TRGI und TRF)
Electric- and gas connection on the heater may be carried out only by a specialist
according to the local directives! (In Germany i.e. TRGI und TRF)
according to the local directives! (In Germany i.e. TRGI und TRF)
Electrical connection:
Electrical connection:
Electrical connection:
The electrical connection is made via a mounted mains cable with plug to a
The electrical connection is made via a mounted mains cable with plug to a
230V/50 Hz-single phase power outlet.
The electrical connection is made via a mounted mains cable with plug to a
230V/50 Hz-single phase power outlet.
230V/50 Hz-single phase power outlet.
The heaters have to be positioned on a level stable non-flammable underground. No danger or
The heaters have to be positioned on a level stable non-flammable underground. No danger or
unreasonable harassment may occur. Therefore a levelled as horizontal as possible surface has to be
The heaters have to be positioned on a level stable non-flammable underground. No danger or
unreasonable harassment may occur. Therefore a levelled as horizontal as possible surface has to be
created.
unreasonable harassment may occur. Therefore a levelled as horizontal as possible surface has to be
created.
created.
The use in basements or below ground level is dangerous and
The use in basements or below ground level is dangerous and
not allowed!
The use in basements or below ground level is dangerous and
not allowed!
not allowed!
The use in fire- and explosion-endangered surrounding is not allowed.
The use in fire- and explosion-endangered surrounding is not allowed.
The use in fire- and explosion-endangered surrounding is not allowed.
The distance to flammable materials should be minimum 1.5 m, on the air outlet side minimum 3 m.
The distance to flammable materials should be minimum 1.5 m, on the air outlet side minimum 3 m.
The distance to flammable materials should be minimum 1.5 m, on the air outlet side minimum 3 m.
Don' t turn the heater towards the gas bottle, there is a fire hazard!
Don' t turn the heater towards the gas bottle, there is a fire hazard!
Don' t turn the heater towards the gas bottle, there is a fire hazard!
Gas connection:
Gas connection:
On the heater is a 3/8"-external thread with inner cone (note left hand thread).
Gas connection:
On the heater is a 3/8"-external thread with inner cone (note left hand thread).
As accessory the Gas heater is equipped with a gas hose, gas hose leakage safety
On the heater is a 3/8"-external thread with inner cone (note left hand thread).
As accessory the Gas heater is equipped with a gas hose, gas hose leakage safety
device, and a pressure regulator with combi bottle connecting thread. The connection to a
As accessory the Gas heater is equipped with a gas hose, gas hose leakage safety
device, and a pressure regulator with combi bottle connecting thread. The connection to a
gas pipe has to be made with suitable adapters (note left hand thread). It is essential to
device, and a pressure regulator with combi bottle connecting thread. The connection to a
gas pipe has to be made with suitable adapters (note left hand thread). It is essential to
ensure sufficient supply pressure and gas volume.
gas pipe has to be made with suitable adapters (note left hand thread). It is essential to
ensure sufficient supply pressure and gas volume.
ensure sufficient supply pressure and gas volume.
Torsion stress (twisting) of the gas hose must be avoided at any case!
Torsion stress (twisting) of the gas hose must be avoided at any case!
Torsion stress (twisting) of the gas hose must be avoided at any case!
Since there are possibly regional differences in the gas composition, the impeccable ignition has to be
Since there are possibly regional differences in the gas composition, the impeccable ignition has to be
checked when starting.
Since there are possibly regional differences in the gas composition, the impeccable ignition has to be
checked when starting.
With non perfect ignition the position of the electrode has to be adjusted.
checked when starting.
With non perfect ignition the position of the electrode has to be adjusted.
This check should be repeated in reasonable intervals.
With non perfect ignition the position of the electrode has to be adjusted.
This check should be repeated in reasonable intervals.
This check should be repeated in reasonable intervals.
The pressure regulator which has to be used must in it's capacity absolutely match the heater's
The pressure regulator which has to be used must in it's capacity absolutely match the heater's
specifications (Connecting pressure and connected load).
The pressure regulator which has to be used must in it's capacity absolutely match the heater's
specifications (Connecting pressure and connected load).
specifications (Connecting pressure and connected load).
Remove gas only in gaseous state – do not use staple gas (liquid extraction)!
Remove gas only in gaseous state – do not use staple gas (liquid extraction)!
Remove gas only in gaseous state – do not use staple gas (liquid extraction)!
Only gas cylinders, which meet the existing directives, may be used. Should ripe form on the gas bottle
Only gas cylinders, which meet the existing directives, may be used. Should ripe form on the gas bottle
(Icing) then the gas discharge amount is above the maximum possible of the gas bottle. In order to avoid
Only gas cylinders, which meet the existing directives, may be used. Should ripe form on the gas bottle
(Icing) then the gas discharge amount is above the maximum possible of the gas bottle. In order to avoid
this, use gas bottles with higher discharge capacity or several gas bottles connected with multiple bottle
(Icing) then the gas discharge amount is above the maximum possible of the gas bottle. In order to avoid
this, use gas bottles with higher discharge capacity or several gas bottles connected with multiple bottle
connector (optional accessory).
this, use gas bottles with higher discharge capacity or several gas bottles connected with multiple bottle
connector (optional accessory).
connector (optional accessory).
The change/exchange of the gas bottles may be done only in a surrounding without ignition source.
The change/exchange of the gas bottles may be done only in a surrounding without ignition source.
The change/exchange of the gas bottles may be done only in a surrounding without ignition source.
6. Installation
6. Installation
6. Installation
40 of 62
40 of 62
40 of 62
Werbung
