Yamaha CP33 Bedienungsanleitung Seite 53

10. SYSTEM EXCLUSIVE MESSAGES (XG Standard)
(1) XG Native Parameter Change
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->
[mmH] -> [llH] -> [ddH] ->...-> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
1nH = When received, n=0~F.
When transmitted, n=0.
4CH = Model ID of XG
hhH = Address High
mmH = Address Mid
llH = Address Low
ddH = Data
|
F7H = End of Exclusive
Data size must match parameter size (2 or 4 bytes).
When an XG System On message is received, the MIDI sys-
tem will be reset to its default settings.
The message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
(2) XG Native Bulk Data (reception only)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->
[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->
[ccH] -> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
0nH = When received, n=0~F.
4CH = Model ID of XG
aaH = Byte Count
bbH = Byte Count
hhH = Address High
mmH = Address Mid
llH = Address Low
ddH = Data
| |
| |
ccH = Check sum
F7H = End of Exclusive
• Receipt of the XG SYSTEM ON message causes reinitializa-
tion of relevant parameters and Control Change values. Allow
sufficient time for processing to execute (about 50 msec)
before sending the CP33 another message.
• XG Native Parameter Change message may contain two or
four bytes of parameter data (depending on the parameter
size).
• For information about the Address and Byte Count values,
refer to Table 1 below. Note that the table's Total Size value
gives the size of a bulk block. Only the top address of the
block (00H, 00H, 00H) is valid as a bulk data address.
11. SYSTEM EXCLUSIVE MESSAGES
(CP33 MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [01H] -> [nnH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = CP33 ID
01H = Product ID (CLP common)
nnH = Substatus
nn Control
02H Internal MIDI clock
03H External MIDI clock
F7H = End of Exclusive
12. SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->
[0nH] -> [ccH] -> [vvH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = CP33 ID
7FH = Extended Product ID
xxH = Product ID 4CH
11H = Special control
0nH = Control MIDI change (n=channel number)
cc = Control number
vv = Value
F7H = End of Exclusive
Control On
Split Point Always 00H
Metronome Always 00H
Sustain Level ch: 00H-0FH
Channel Detune ch: 00H-0FH
Voice Reserve ch: 00H-0FH
* When Volume or Expression is received for Reserve On, they
will be effective from the next Key On. Reserve Off is normal.
13. SYSTEM EXCLUSIVE MESSAGES
(Master Setting Bulk)
Bulk Request (reception only)
Data format: [F0H] -> [43H] -> [2nH] -> [7FH] -> [05H] ->
[33H] -> [00H] -> [00H] -> [F7H]
F0H= Exclusive Status
43H= Yamaha ID
2nH= When received, n=0.
7FH= CP33 ID High
05H= CP33 ID Low
33H= Master Setting Address High
00H= Master Setting Addres Mid
00H= Master Setting Addres Low
F7H= End of Exclusive
Bulk Data
Data format: [F0H] -> [43H] -> [0nH] -> [7FH] -> [05H] ->
[04H] -> [0EH] -> [33H] -> [00H] -> [00H] ->
[dtH] -> [ccH] -> [F7H]
F0H= Exclusive Status
43H= Yamaha ID
0nH= When transmitted, n=0.
7FH= CP33 ID High
05H= CP33 ID Low
04H= Byte Count
0EH= Byte Count
33H= Master Setting Address High
00H= Master Setting Addres Mid
00H= Master Setting Addres Low
dtH= Data
ccH= Check sum
F7H= End of Exclusive
14. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]
-> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H]
Master Tuning (XG and last message priority) simultaneously
changes the pitch of all channels.
F0H = Exclusive Status
43H = Yamaha ID
1nH = When received, n=0~F.
When transmitted, n=0.
27H = Model ID of TG100
30H = Sub ID
00H =
00H =
mmH = Master Tune MSB
llH = Master Tune LSB
ccH = irrelevant (under 7FH)
F7H = End of Exclusive
MIDI-Datenformat
ccH vvH
14H 14H: Split Key Number
1BH 00H: No accent
01H-0FH: 1/4-15/4
7FH: off
3DH (Sets the Sustain Level
for each channel)
00H-7FH
43H (Sets the Detune value
for each channel)
00H-7FH
45H 00H : Reserve off
7FH : on*
Bedienungsanleitung CP33
53