Protecting The Environment - DeWalt DW712 Handbuch

EN G LI S H
Right side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
OUTSIDE CORNER
Left side
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
Right side
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
GROOVING (FIG. T)
Your saw is equipped with a grooving stop (12) and grooving depth
adjustment knob (15) to allow for groove cutting.
• Flip the grooving stop (12) towards the front of the saw.
• Adjust the grooving depth adjustment knob (15) to set the depth of
the groove cut. It might be necessary to release the lock nut (66)
first.
• Place a piece of scrap material of approx. 5 cm between fence and
workpiece in order to perform a straight groove cut.
DUST EXTRACTION (FIG. A2 & A5)
This machine is provided with a dust extraction point (24) for connection
of a dust extraction kit (36) (available as an option).
WARNING! Whenever possible, connect a dust extraction
device designed in accordance with the relevant regulations
regarding dust emission.
Connect a dust collection device designed in accordance with the
relevant regulations. The air velocity of externally connected systems
shall be 20 m/s +/- 2 m/s. Velocity to be measured in the connection
tube at the point of connection, with the tool connected, but not
running.
CUTTING SMALL PIECES (FIG. J1)
The upper part of the left side of the fence (3) can be adjusted to
provide maximum support when cutting small pieces.
• Put the saw blade into vertical position.
• Loosen the plastic knob (29) at least 3 full turns.
• Adjust the fence as close to the blade as possible.
• Tighten the knob securely.
SUPPORT FOR LONG PIECES (FIG. A4)
• Always support long pieces.
• For best results, use the extension work support (35) to extend the
table width of your saw (available from your dealer as an option).
Support long workpieces using any convenient means such as
saw-horses or similar devices to keep the ends from dropping.
SAW BLADES
To obtain the stated cutting capacities, always use 216 mm saw blades
with 30 mm arbor holes. Consult your dealer for further information on
the appropriate accessories.
TRANSPORTING (FIG. A6, B2)
In order to conveniently carry the tool, a carrying strap can be attached
to the base. The carrying strap (see fig. A6) is available as an option.
• To transport the saw, lower the head and depress the lock down
pin (14).
• Lock the rail lock knob with the saw head in the front position, lock
the mitre arm in the right mitre angle, slide the fence (3) completely
inward and lock the bevel lever (11) with the saw head in the
vertical position to make the tool as compact as possible.
• Always use the hand indentations (30) shown in fig. B2 to transport
the saw.
34
MAINTENANCE
Your D WALT power tool has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental start-
up can cause injury.
Cleaning
Before use, carefully check the upper blade guard, movable lower
blade guard as well as the dust extraction tube to determine that it will
operate properly. Ensure that chips, dust or workpiece particle cannot
lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and
guards disconnect the machine from the power supply and follow the
instructions given in section Mounting the Saw Blade. Remove the
jammed parts and reassemble the saw blade.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
CLEANING AND MAINTAINING THE KERF PLATE (FIG. U)
Regularly clean the area below the kerf plate.If the kerf plate is worn it
must be replaced.
• Remove the screws (67) holding the kerf plate (31).
• Remove the kerf plate and clean the area below.
• Re-install the parts of the kerf plate and the screws.
• Tighten the screws hand-tight.
• To adjust the kerf plate, proceed as follows:
• Pull down the head until the blade just enters the saw kerf.
• Adjust each part of the kerf plate to fit closely to the teeth of the
blade.
• Tighten the screws.

Protecting the Environment

Separate collection. This product must not be disposed of with
normal household waste.
Should you find one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of
recycled materials helps prevent environmental pollution
and reduces the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
WALT product needs replacement,
E