Intended Use - Makita TW161D Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
F astening c apac ities
S q uare d riv e
No load speed
I mpac ts per minute
O v erall length
R ated v oltage
Net w eigh t
Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
Specifications may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est c ombination, a c c or d ing to E P T A - P ro c e d ure 0 1 / 20 1 4 , are s h o w n in t h e table.
Applicable battery cartridge and charger
Battery cartridge
C h arger
Some of the battery cartridges and chargers listed above may not be available depending on your region of
resi d en c e.
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
WARNING:
and chargers may cause injury and/or fire.

Intended use

T h e tool is inten d e d f or f astening bolts an d nuts.
Noise
The typical A-weighted noise level determined accord-
ing to EN 6 2 8 4 1 -2-2 :
Sound pressure level (L
pA
Sound power level (L ) :
W A
Uncertainty (K) : dB(A)
NOTE: The declared noise emission value(s) has
been measure d in a c c or d an c e w it h a stan d ar d test
method and may be used for comparing one tool with
anot h er.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
e x posure.
S tand ard bolt
H igh tensile bolt
H ard impac t mod e
S of t impac t mod e
H ard impac t mod e
S of t impac t mod e
) : dB(A)
dB (A)
D .C . 1 0.8 V - 1 2 V max
BL 1 01 5 / BL 1 01 6 / BL 1 020B / BL 1 021 B / BL 1 04 0B / BL 1 04 1 B
D C 1 0S A / D C 1 0S B / D C 1 0W C / D C 1 0W D / D C 1 8 R E
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mine d a c c or d ing to EN 6 2 8 4 1 -2-2 :
W ork mo d e : impa c t tig h tening o f f asteners o f t h e ma x i-
mum capacity of the tool
Vibration emission (a
Uncertainty (K) : . m/s
NOTE: The declared vibration total value(s) has been
measure d in a c c or d an c e w it h a stan d ar d test met h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
4 ENGLISH
TW161D
M8 - M1 6
M6 - M1 2
1 2.7 mm
-1
0 - 2,4 00 min
-1
0 - 1 ,300 min
-1
0 - 3,6 00 min
-1
0 - 2,000 min
1 5 0 mm
1 .0 - 1 .2 kg
) : . m/s
2
h
2