Intended Use - Makita DTDA070 Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening capacities
Maximum fastening torque
Torque range
No load speed (RPM)
Impacts per minute
Rated voltage
Overall length
Net weight
Applicable USB cable
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DTDA040
Sound pressure level (L
Sound power level (L ) : 101 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTDA070
Sound pressure level (L
Sound power level (L ) : 103 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTDA100
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model DTDA140
Sound pressure level (L
Sound power level (L ) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Standard bolt
High tensile bolt
) : 90 dB(A)
pA
) : 92 dB(A)
pA
) : 94 dB(A)
pA
) : 94 dB(A)
pA
DTDA040 DTDA070
M5 - M10
M5 - M8
35 N•m 65 N•m
Approx. 3 - 20 Approx. 5 - 40
N•m N•m
-1
0 - 2,400 min 0 - 2,500 min
-1
0 - 3,700 min
139 mm
1.1 - 1.4 kg
BL1415N / BL1415NA / BL1430B / BL1440 / BL1460A / BL1460B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH / DC18WC
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
5 ENGLISH
DTDA100 DTDA140
M5 - M12 M6 - M16
M5 - M10 M6- M12
95 N•m 140 N•m
Approx. 6 - 65 Approx. 18 - 80
N•m
-1
0 - 2,700 min
0 - 3,300 min
D.C. 14.4 V
146 mm
1.2 - 1.4 kg 1.2 - 1.5 kg
661432-2
N•m
-1
-1