Makita HM1213C Betriebsanleitung Seite 6

Loosen the six screws and remove the handle. Note that
the top screws are different from other screws. (Fig. 12)
Disconnect the connector by pulling them. (Fig. 13)
Loosen the four screws on crank cap and remove the
crank cap cover. (Fig. 14)
Wipe out the old grease inside and replace with a fresh
grease (60 g). Use only Makita genuine hammer grease
(optional accessory). Filling with more than the specified
amount of grease (approx. 60 g) can cause faulty
hammering action or tool failure. Fill only with the
specified amount of grease. (Fig. 15)
CAUTION:
• Be careful not to damage the connector or lead wires
especially when wiping out the old grease.
To reassemble the tool, follow the disassembling
procedure in reverse.
CAUTION:
• Do not tighten the crank cap excessively. It is made of
resin and is subject to breakage. (Fig. 16)
Connect the connector firmly and then reinstall the
handle.
CAUTION:
• Be careful not to damage the connector or lead wires
especially when installing the handle.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Bull point (SDS-max)
• Cold chisel (SDS-max)
• Scaling chisel (SDS-max)
• Clay spade (SDS-max)
• Bit grease
• Safety goggles
• Hammer grease
• Plastic carrying case
For Model HM1213C
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 2.5 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745-2-6:
Work mode: chiseling function with side handle
Vibration emission (a
Uncertainty (K): 1.5 m/s
6
ENG102-2
): 75 dB (A)
pA
): 95 dB (A)
WA
ENG216-1
2
): 7.0 m/s
h,CHeq
2
For Model HM1203C
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 2 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745-2-6:
Work mode: chiseling function with side handle
Vibration emission (a
Uncertainty (K): 1.5 m/s
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machin(s):
Designation of Machine: Demolition Hammer
Model No./ Type: HM1213C, HM1203C
are of series production and
Conforms to the following European Directives:
2000/14/EC, 98/37/EC until 28th December 2009 and
then with 2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex VIII.
Notified Body:
TÜV Rheinland Product Safety GmbH, identification
no. 0197
Model HM1213C
Measured Sound Power Level: 95 dB
Guaranteed Sound Power Level: 97 dB
Model HM1203C
Measured Sound Power Level: 95 dB
Guaranteed Sound Power Level: 98 dB
16th January 2009
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
): 81 dB (A)
pA
): 95 dB (A)
WA
2
): 15.5 m/s
h,CHeq
2
Director
ENG102-2
ENG216-1
ENH213-1