Functional Description - Makita HR5201C Betriebsanleitung

13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
FOR MODEL HR5211C
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
FOR MODELS HR5210C/HR5201C
Trigger switch
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
• This switch functions when setting the tool in
and symbol modes.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Slide switch
CAUTION:
• Before plugging in the tool, always check to see that
the tool is switched off.
• This switch functions only when setting the tool in
symbol action mode.
When using the tool in the hammering mode for a long
time, the slide switch is available. To start the tool, push
the "I (ON)" side of the switch lever. To stop the tool, push
the "O (OFF)" side of the switch lever. (Fig. 2)
Speed change (Fig. 3)
The revolutions and blows per minute can be adjusted just
by turning the adjusting dial. The dial is marked 1 (lowest
speed) to 5 (full speed).
Refer to the table below for the relationship between the
number settings on the adjusting dial and the revolutions/
blows per minute.
Number on
adjusting dial
5
4
3
2
1
CAUTION:
• If the tool is operated continuously at low speeds for a
long time, the motor will get overloaded, resulting in
tool malfunction.
• The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
Selecting the action mode
Rotation with hammering (Fig. 4 & 5)
For drilling in concrete, masonry, etc., depress the lock
button and rotate the change lever so that the pointer
points to the
bit.
Hammering only
FOR MODEL HR5201C AND HR5210C (Fig. 6)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
chisel, scaling chisel, etc.
For long time hammering (FOR MODELS HR5201C
AND HR5210C ONLY) (Fig. 7)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
symbol
chisel, scaling chisel, etc.
CAUTION:
• When using the tool in the
trigger does not work and only the slide switch works.
FOR MODEL HR5211C (Fig. 8)
For chipping, scaling or demolition operations, depress
the lock button and rotate the change lever so that the
pointer points to the
chisel, scaling chisel, etc.
CAUTION:
• Do not rotate the change lever when the tool is running
under load. The tool will be damaged.
• To avoid rapid wear on the mode change mechanism,
be sure that the change lever is always positively
located in one of the two or three action mode
positions.
Torque limiter
The torque limiter will actuate when a certain torque level
is reached. The motor will disengage from the output
shaft. When this happens, the bit will stop turning.
Revolutions per
Blows per minute
minute
260
240
190
150
130
symbol. Use a tungsten-carbide tipped
symbol. Use a bull point, cold
symbol. Use a bull point, cold
symbol mode, the switch
symbol. Use a bull point, cold
2,150
2,000
1,600
1,250
1,075
7