lamber PS-F85-SRS/BT Bedienungsanleitung Seite 22

cycle can be interrupted at any time pressing again
button "C" that will let final sequences start.
Self-washing cycle: with machine on, carry out the
following operations:
- Remove the overflow from the tank and wait
for the tank's emptying (for machines with
drain pump, look at the instructions in the
specific paragraph),
- Close the door of the glasswasher,
- Keep pressed the cycle button ''C'' during 3
seconds: lamp ''2'' flashes during all the length
of the 5 or 10 minutes cycle, according to the
rinse's duration fixed by default.
ACHIEVEMENTS
Any deficiency in the washing process is apparent
when dirty residuals are visible. An insufficient rinsing
might cause any halos: in this case, check that the
rinsing jets are clean and there is a sufficient pressure
in the water distribution network.
In the case that residuals are present, check that:
• the washing jets are clean
• there is detergent
• the pump suction filter is clean
• the positions of the objects in the rack are correct.
DISHES POSITIONING
It is suitable to place dishes, inside the plastic basket
with the concave side facing upwards. Place mixed
cutlery in a vertical position into the suitable container
minding not to cram them and with handgrips towards
the bottom (see drawing).
RINSING ADDITIVES
To grant a perfect rinsing, a quick drying and to
avoid calcareous sediments on glasses and
you must add a surfactant on water (Brightener).
Your cleansing agent supplier will be able to suggest
the most suitable product. Your machine is equipped
with a rinse aid dispenser. Mean concentration used
REGENERATING
(for machines with Water softener)
If the glass-washer is equipped with a Water softener
the regeneration of resins is automatic according to
parameters fixed by the producer.
According to the water hardness, it is possibile to
modify the programming of the regeneration. See the
corresponding table in the installer section.
N.B. each 90 seconds of tank filling
duration, the machine stops for about
2 minutes
regeneration.
SALT CONTROL
When it is necessary to add salt in the container, the
green lamp "E" is flashing.
Unscrew the plug of the salt container at the bottom of
the tank and put 1 kg coarse salt tablets in it. Clean the
gasket and screw the plug.
Attention!
The lack of salt in the container damages the machine
because of limestone, besides a defective washing of
glasses and dishes.
These damages are not covered by the warranty.
DRAIN PUMP INSTRUCTION
(only for machines with drain pump)
The drain pump starts up automatically just
during the washing cycle to discharge the
exceeding water coming from the rinsing cycle.
At the end of the working day, in order to
completely discharge the tank, it is necessary
to perform the following operations:
1. Open the door of the dishwasher
2. Remove the overflow pipe from the tank;
3 .Afterwards push button "F" for 3 seconds.
Alternatively are flashing the control lamp "E" and
the cycle lamp (chosen before)
The discharge will stop automatically after 5
minutes. The control lamps will stop flashing.
Please note: in case the door is open the control
lamp "E" will continue flashing.
Reinstall the flow over and shut the door.
CLEANSING AGENTS
The choice of a suitable cleansing agent is an
cups
essential condition if you want to obtain extremely
good washing results as regards hygienic results.
That's why it's important to consider some points.
First of all only highly alkaline and chlorine-active
antifoam products, especially made for industrial dish-
washing machines, must be used and they must be
produced
concentration of the cleansing agents in powder must
be 1,5÷2,5 g/lt. Mean concentration of liquid cleansing
agents must be 2÷4 g/lt.
In order to avoid scales and corrosions, put cleansing
agent above water level on the nearest area of the
sucking pump filter, in this way it will immediately
dilute and will not deposit on the tank bottom.
22
to carry
by well-known reliable
out the
Firms. Mean