Kenwood KDC-4754SD Bedienungsanleitung Seite 14

[AUDIO CONTROL] / [AUDIO CTRL] : While listening to any source except in STANDBY state...
Item
EQ PRO
BASS ADJUST BASS CTR FRQ/ BASS C FRQ
BASS LEVEL
BASS Q FACTOR/ BASS Q
FCTR
BASS EXTEND
MID ADJUST MID CTR FRQ/ MID C FRQ
MID LEVEL
MID Q FACTOR/ MID Q FCTR 0.75/ 1.00 */ 1.25: Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ/ TRE C FRQ
TRE LEVEL
PRESET EQ NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL: Selects a preset sound mode
suitable to the music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS BOOST B.BOOST LV1/ B.BOOST LV2/ B.BOOST LV3: Selects your preferred bass boost level. ;
B.BOOST OFF *: Cancels.
LOUDNESS LOUDNESS LV1 */ LOUD LV1 */ LOUDNESS LV2/ LOUD LV2: Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low volume level. ;
LOUDNESS OFF/ LOUD OFF: Cancels.
BALANCE L15 — R15 (Preset: 0): Adjusts the left and right speaker output balance.
FADER R15 — F15 (Preset: 0): Adjusts the rear and front speaker output balance.
SUBWOOFER SET/ ON *: Turns on the subwoofer output. ; OFF: Cancels.
SUB-W SET
DETAILED SET/ DETAIL SET
HPF THROUGH *: All signals are sent to the speaker. ; 100HZ/ 120HZ/ 150HZ: Frequencies lower than the
specified value are cut off.
LPF SUBWOOFER/ THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies higher than
LPF SUB-W specified value are cut off.
SUB-W PHASE REVERSE/ REV (180°)/ NORMAL/ NORM (0°) *: Selects the phase angle of the subwoofer output to
be in line with the speaker output for optimum performance. (Selectable only if a setting other than
[THROUGH] is selected for [LPF SUBWOOFER/ LPF SUB-W].)
SUPREME SET ON *: Creates realistic sound by interpolating the high-frequency components that are lost in AAC/
MP3/WMA audio compression. ; OFF: Cancels. (Selectable only when playback an AAC/MP3/WMA
disc or a USB device, except iPod.)
VOLUME OFFSET/ –8 — +8 (for AUX) ; –8 — 0 (for other sources): Presets the volume adjustment level of each
VOL OFFSET source. The volume level will automatically increase or decrease when you change the source. (Before
(Preset: 0) making an adjustment, select the source you want to adjust.)
14
Selectable setting (Preset: *)
60/ 80/ 100 */ 200: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.
1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
ON: Turns on the extended bass. ; OFF *: Cancels.
0.5K/ 1.0K */ 1.5K/ 2.5K: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.
10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.