Maintenance - AEG POWERBASE 40 MB Gebrauchsanleitung

TECHNICAL DATA
Voltage range ........................ 9,6-18 V.....................24 V
Quick charge current ...................2,3 A....................1,6 A
Maintaining charge .....................100 mA................100 mA
Battery charging time
1,4 Ah ............................approx 38 min ..... approx 55 min
1,7 Ah ............................approx 50 min ..... approx 70 min
2,0 Ah ............................approx 55 min ..... approx 80 min
2,2 Ah ............................approx 65 min ..... approx 90 min
2,4 Ah ............................approx 70 min ... approx 100 min
Weight ........................................500 g ...................500 g
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the attached
leaflet!
Do not dispose of used battery packs in the household refuse
or by burning them. AEG Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System 3000 chargers for charging System 3000
battery packs. Do not use battery packs from other systems.
The following battery packs can be charged with this charger:
voltage battery
7,2 V B 7.2-range
9,6 V B 9.6-range
12 V B 12-range
14,4 V B 14.4-range
18 V B 18-range
24 V B 24-range
9,6 V M 9.6-range
12 V M 12-range
14,4 V M 14.4-range
Do not try to charge non-chargeable batteries with this
charger.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Never break open battery packs and chargers and store only
in dry rooms. Keep dry at all times.
Please pay attention to the following symbol on the label of
the charger:
This tool is only suitable for indoor use. Never expose
tool to rain.
The battery clamps of the charger are fed by the mains
supply. Do not touch the tool with conducting objects.
Never charge a damaged battery pack. Replace by a new
one.
Before use check machine, cable, and plug for any damages
or material fatigue. Repairs should only be carried out by
authorised Service Agents.
SPECIFIED CONDITIONS OF USE
The quick charger can charge AEG batteries from 9.6 V to 24
V.
Do not use this product in any other way as stated for normal
use.
MAINS CONNECTION
Connect only to a single-phase AC current supply and only to
the mains voltage specified on the rating plate. Connection to
sockets without earth protection is possible as the appliance
features protective insulation to IEC 335. Radio suppression
complies with the European standard EN 55014.
5 ENGLISH
rating No. of
(of storage battery) battery
cells
1,4 Ah 6
1,4 Ah 8
1,2 Ah 10
1,4 Ah 12
1,4 Ah 15
1,4 Ah 20
2,2 Ah 8
2,2 Ah 10
2,2 Ah 12
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
General note concerning NiMH batteries:
The capacity of the battery is reduced when the temperature
falls below -10°C.
Long-term storage at temperatures higher than +40°C may
have negative effects on the capacity of the battery.
CHARACTERISTICS
After inserting the battery into the reception of the charger the
battery will automatically be charged (control lamp is
illuminated continuously)
When a hot or cold battery pack is inserted into the charger
(flashing lamp), charging will begin automatically once the
battery reaches the correct charging temperature.
Standard charging time is approximately 38 minutes (1.4 Ah
battery). Charging time varies depending on the battery
temperature, charge needed and the type of battery pack
being charged.
As soon as charging is completed, the charger switches over
to "trickle" charge to maintain the full capacity (lamp is
switched off).
The battery can be stored permanently in the charger without
the danger of being overcharged.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60335, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 73/23/EEC, 89/336/EEC

MAINTENANCE

If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appopinted by the manufacturer,
because special purpose tools are required
Use only AEG accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents (see
our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the ten-digit No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Atlas Copco Electric Tools
GmbH, Postfach 320, D-71361 Winnenden.
SYMBOLS
The battery clamps of the charger are fed by
mains supply. do not touch the tool with
conducting objects.
Manager Product Marketing and
Development