Herunterladen Inhalt Inhalt Diese Seite drucken

Panasonic EY75A2 Bedienungsanleitung Seite 12

Akku-schlagschrauber
Vorschau ausblenden Andere Handbücher für EY75A2:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 21
Variable Speed Control Trigger
To set the center of a hole, pull the trigger
slightly to start the bit rotation slowly.
The more the speed control trigger is
pulled, the higher the speed becomes.
CAUTION:
When operating the tool by pulling the
trigger, there may be a momentary lag
before rotation starts. This does not signal
a malfunction.
• This lag occurs as the tool's circuitry
starts up when the trigger is pulled for
the first time after installing a new bat-
tery pack or after the tool has not been
used for at least 1 minute (or at least 5
minutes when the LED is on). Rotation
will start without any lag during second
and subsequent operations.
Control Panel
(1)
(1) Impact Power Mode Select
Selecting the impact power among 3
modes (Soft, Medium, Hard).
Press the impact power mode button to set
it. The mode changes to hard, medium, or
soft each time the button is pressed.
The driver is preset to "hard" impact mode
setting when shipped from the manufac-
turer.
Recommended work guideline table
Impact
Power mode
Recommended Application
Display
Jobs requiring a high level
H
of torque where there is
no possibility of the bolts
or screw breaking, its top
shearing off, or the bit coming
0 – 2300 r.p.m./
loose. (This setting provides
0 – 2500 r.p.m.
maximum torque.) Suitable
applications include:
and
Tightening M8 and larger
0 – 3000 i.p.m./
bolts
0 – 3500 i.p.m.
Tightening long screws
during interior finishing work
(4) (3)
(2) LED light
(2)
Caution : DO NOT STARE INTO BEAM.
Use of controls or adjustments or performance
of procedures other than those specified herein
may result in hazardous radiation exposure.
- 12 -
Jobs requiring limited torque
M
where there is a possibility of
the screw breaking or its top
shearing off. (This setting limits
torque.) Suitable applications
include:
0 – 1400 r.p.m.
Tightening bolts with
and
smaller diameters (M6)
0 – 2800 i.p.m.
Tightening metalwork
screws when installing
fixtures
Jobs requiring limited torque
S
where there is a possibility
of the screw breaking, its
top shearing off, or the bit
coming loose and damaging
a finished exterior surface.
(This setting limits torque.)
0 – 1000 r.p.m.
Suitable applications include:
and
Tightening bolts smaller
than M6 that may shear
0 – 2000 i.p.m.
easily
Tightening screws into
molded plastic
Installing gypsum wallboard
* i.p.m. = Impact per minute.
Avoid repeatedly depressing the switch
when the bolts and screws are securely
fastened.
Not doing so may cause a delay in
rotation starting, or the Impact Power
mode display to flash and prevent rotation
from starting for circuit protection.
Pressing the
tog gles the LED light on
and off.
The light illuminates
w i t h v e r y l o w c u r -
rent, and it does not
adversely affect the per-
formance of the driver
during use or its battery
capacity.
CAUTION:
• The built-in LED light is designed to illu-
minate the small work area temporarily.
• Do not use it as a substitute for a regu-
lar flashlight, since it does not have
enough brightness.
• LED light turns off when the tool has not
been used for 5 minutes.
but ton

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ey75a1

Inhaltsverzeichnis