Startup / Operation - BOMANN DU 652.1 IX Bedienungsanleitung, Garantie

• For mounting the hood drill in total 9x mounting
holes with approx. 8 mm diameter into the wall.
Insert the supplied dowels.
• Affix the brackets (01) for the hood body and (02)
for the upper shaft end at the pre-marked
positions using the screws 5x ST4x40mm
• Before inserting the hood, affix the connection
piece with the non-return valves from the top of
the extraction duct.
For the exhaust mode (Fig. 2): For the exhaust mode (Fig. 2): For the exhaust mode (Fig. 2): For the exhaust mode (Fig. 2):
• Hereupon a flexible exhaust hose (supplied) with
an inner diameter of 150 mm must be attached.
• Hang up the hood body. Check the secure hold
and the horizontal position
• Secure the housing with the screws 2x ST4*30
through the hood body
• Fasten the outer (lower) shaft with the bracket
(03) using the metal screws 2x ST4*8
• Put the shaft unit on and fasten the shaft bracket
(03) with the screws 2x ST4*40
For the exhaust mode For the exhaust mode For the exhaust mode For the exhaust mode: : : :
• Check the correct position of the exhaust hose
and connect it with the outlet opening.
• Pull up the inner shaft and fix the shaft cover to
the side with the bracket (02) using the screws
(Fig. 7 (Fig. 7 (Fig. 7 (Fig. 7) ) ) )
2x ST4*8 .
Installing the activated carbon filter for recirculation Installing the activated carbon Installing the activated carbon Installing the activated carbon
mode mode
mode mode
• Remove the aluminum grease filter.
• Place the carbon filter onto the air intake of the
extraction duct. Make sure that the mounting pins
on the extraction duct engage the mounting slots
of the carbon filter. Turn the filter clockwise until it
clicks into place.
• Reinstall the aluminum grease filter.
All manuals and user guides at all-guides.com
(Fig. 1 1 1 1 ) ) ) ) (Fig. (Fig. (Fig.
(Fig. 3 3 3 3 ) ) ) ) (Fig.
(Fig. (Fig. .
(Fig. 4) (Fig. 4) (Fig. 4) (Fig. 4)
.
(Fig. 5). ). ). ). (Fig. 5
(Fig. 5 (Fig. 5
(Fig. (Fig. 6 6 6 6 ) ) ) ) (Fig. (Fig.
.
filter for recirculation filter for recirculation filter for recirculation
Electrical connection Electrical connection Electrical connection Electrical connection
WARNING: WARNING: WARNING: WARNING:
• The installation to the mains supply must conform
to the local standards and regulations.
• Improper connection may cause to an electric
.
shock shock! shock shock
• Do not modify the appliance plug. If the plug does
not fit properly to the outlet, let install a proper
outlet by an authorized specialist.
• The accessibility of the power plug must be en-
sured to disconnect the appliance from the power
supply in case of emergency.
• Ensure that your mains power corresponds with
the specifications of the appliance. The specifica-
tions are printed on the rating label.
• Connect the mains cable to a properly installed
and earthed wall outlet.
• If the plug after installation is not accessible, a
corresponding disconnect device must be availa-
ble to meet the relevant safety regulations.

Startup / Operation

Startup / Operation Startup / Operation Startup / Operation
The hood is to operate via two slide switches. The
lighting as well as the fan settings must be switched
on and off with the corresponding switches.
Power level Power level
Power level Power level
0 0 0 0 off I I I I low
Lighting Lighting Lighting Lighting
0 0 0 0 lighting off
Settings Settings Settings Settings
I Power level: : : : Suitable for cooking on a low flame I Power level
I Power level I Power level
and for dishes which produce no or little steam, in
order to circulate the air around the kitchen.
II Power level II Power level: : : : Suitable for normal cooking. II Power level II Power level
18
electric electric electric
II II II II medium III III III III high
I I I I lighting on