In The Case Of Right Bevel Cut - Makita LS002G Betriebsanleitung

Example:
In the case of cutting 52/38° type crown molding for
position (a) in the above figure:
• Tilt and secure bevel angle setting to 33.9° LEFT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on the
saw.
• The finished piece to be used will always be on
the LEFT side of the circular saw blade after the
cut has been made.

In the case of right bevel cut

(a) (b)
1. Inside corner 2. Outside corner
Table (A)
– Molding Bevel angle
position
52/38°
in the
type
figure
For (a) Right
inside 33.9°
corner
(b)
For (c)
outside
(d)
corner
Table (B)
– Molding
position in
the figure
For inside (a)
corner
(b)
For outside (c)
corner
(d)
(c) (d)
1 2
Miter angle
45° type 52/38°
type
Right Right
30° 31.6°
Left
31.6°
Right
31.6°
Molding Finished
edge against piece
guide fence
Wall contact Finished
edge should piece will be
be against on the Right
guide fence. side of blade.
Ceiling
contact edge
Finished
should be
piece will be
against guide
on the Left
fence.
side of blade.
Wall contact
edge should
be against
guide fence.
Example:
In the case of cutting 52/38° type crown molding for
position (a) in the above figure:
• Tilt and secure bevel angle setting to 33.9° RIGHT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on the
saw.
• The finished piece to be used will always be on
the RIGHT side of the circular saw blade after the
cut has been made.
Cutting aluminum extrusion
► Fig.51: 1. Vise 2. Spacer block 3. Guide fence
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in the figure to prevent
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the circular saw blade.
WARNING:
round aluminum extrusions. Thick or round alumi-
num extrusions can be difficult to secure and the work
may loosen during the cutting operation which may
result in loss of control and serious personal injury.
Groove cutting
WARNING:
type of cut by using a wider type blade or dado
blade. Attempting to make a groove cut with a wider
45° type
blade or dado blade could lead to unexpected cutting
results and kickback which may result in serious
personal injury.
Right
35.3°
WARNING:
to the original position when performing other
Left
35.3°
than groove cutting. Attempting to make cuts with
the stopper arm in the incorrect position could lead to
Right
unexpected cutting results and kickback which may
35.3°
result in serious personal injury.
For a dado type cut, perform as follows:
1.
Adjust the lower limit position of the circular saw
blade using the adjusting screw and the stopper arm to
limit the cutting depth of the circular saw blade. Refer to
the section for stopper arm.
2. After adjusting the lower limit position of the circu-
lar saw blade, cut parallel grooves across the width of
the workpiece using a slide (push) cut.
► Fig.52: 1. Cut grooves with blade
3. Remove the workpiece material between the
grooves with a chisel.
29 ENGLISH
4. Aluminum extrusion 5. Spacer block
Never attempt to cut thick or
Do not attempt to perform this
Be sure to return the stopper arm