Inhaltsverzeichnis
Werbung
6.2.
SQUEEGEE AND SPLASH GUARD
ASSEMBLY, DISASSEMBLY AND
ADJUSTMENT
The squeegee is the main component that ensures
perfect drying.
6.2.1. SQUEEGEE ASSEMBLY
Slightly screw the two knobs ( Photo L - 7 ) into the
squeegee body and insert the squeegee into the
slots situated on the squeegee support.
Screw the two knobs ( Photo L - 7 ) in order to secure
the squeegee to the support.
Firmly insert the suction hose ( Photo L - 1 ) into the
pipe in the squeegee body.
6.2.2. SQUEEGEE DISASSEMBLY
Disconnect the suction hose from the squeegee
body.
Unscrew the two knobs ( Photo L - 7 ) that secure the
squeegee to its support and pull the squeegee to free it.
6.2.3. SQUEEGEE BLADES DISASSEMBLY /
ASSEMBLY
Disassemble the squeegee from its support (see 7.2.2)
Unscrew the knobs ( Photo L - 7 ) ( Photo L - 3 ) placed
on the squeegee body and apply some pressure on
their bolts in order to push out the plastic support of
the squeegee blades from the squeegee body.
Tear off the rubber blades from the plastic support.
Assemble the new blades on the plastic support by
the means of the plastic pins that have to be fixed in
the holes placed the blades.
Push the plastic support of the squeegee blades into
the squeegee body and screw the knobs ( Photo L - 7 )
to secure it to the squeegee body.
Reassemble the squeegee to its support (see 7.2.1).
6.2.4. SQUEEGEE ADJUSTMENT
The knob screw on the squeegee support ( Photo L -
2 ) adjusts the squeegee's inclination with respect to
the floor. The two red knobs on the sides, connected
to the rear wheels of the squeegee ( Photo L - 5 ) are
to adjust the pressure of the squeegee to the floor.
When the squeegee is perfectly adjusted, the rear
squeegee blade, sliding as it moves, bends in all
points forming an angle of 45° with the floor.
As the machine operates (advances), the knobs ( Photo
L - 2 ) ( Photo L - 5 ) can be used to adjust the inclination
and pressure of the squeegee blades on the floor.
Squeegee drying must be uniform along the entire
drying line: damp patches mean that drying is insuffi-
cient; turn the adjustment knobs to optimize drying.
6.2.5. SPLASH GUARD ASSEMBLY/ DISASSEMBLY
The splash guard is assembled to the brush plate with
a spring holder linked to the brush plate itself ( Photo
M - 1 ).
To disassemble the splash guard simply detach the
spring holder and pull the splash guard.
To reassemble, fix the splash guard in the brush plate,
and then hook the steel cable to one side of the plate
and the spring holder to the other side of the brush
plate.
6.3.
BRUSH ASSEMBLY / DISASSEMBLY
• Never use the machine if brushes or scrapers and
abrasive disks are not perfectly installed.
Assembly:
Make sure that the brush plate is raised; otherwise lift
it by following the instructions provided in the spe-
cific section.
Make sure that the ignition key on the control panel
is in position "0".
Bring the brushes (or the guide disks equipped with
abrasive disks) near the connections, under the brush
plate; lower the washing plate and start the brushes
turning: the brushes/discs couple automatically;
• Do not allow the length of the rows of brushes to
become lower than 1 cm.
• Do not allow the thickness of the abrasive disks to
become less than 1 cm.
Working with excessively worn brushes or excessi-
vely thin abrasive disks may damage the machine
and the floor.
Regularly check the wear on these parts before star-
ting to work.
Disassembly or replacement:
Make sure that the brush plate is raised; otherwise lift
it by following the instructions provided in the spe-
cific section.
Make sure that the ignition key on the control panel
is in position "0".
While holding the brushes (or the guide disks) with
the hands under the plate, turn them in the rotation
direction while lowering to release them from the
guide plate.
6.4.
FILLING AND DRAINING THE DETERGENT
SOLUTION TANK
☞ The temperature of the water or the detergent
should never exceed 50°C.
• Always empty the detergent solution tank before
filling it up.
To fill:
• Remove the plug in the front of the machine .
• Leave 2 cm between the mouth of the plug and the
liquid level. Do not fill beyond this point!
• Add the required quantity of the chemical product,
considering the percentage indicated by the sup-
plier, with reference to the full tank capacity listed on
the product sheet.
• Use only those products suitable for the floor and
the dirt to be removed.
• The machine was designed to be used with non-
31
Werbung
Inhaltsverzeichnis
