Inhaltsverzeichnis
Werbung
control level, lower the washing unit, levering with
your foot on the brush plate control lever .
Move forwards, pulling the forward lever up or push
it down to reverse . Remember to lift the floor cleaner
before reversing to avoid damaging it.
Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.7.4. INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Check the connection between the power and batte-
ry connector, located under the control panel.
Put the ignition key in and turn it.
Check battery charge status via the control unit and,
if sufficient, operate the brush control key. Now open
the solution cock by lowering the detergent dosa-
ge lever which is at the back of the machine, lower
the brushing unit by levering with your foot on the
brush plate control lever. Move forwards, pulling the
forward lever up .
Allow the detergent solution to work on the dirt
according to what is indicated in the information
relative to the detergent used.
Second set of operations:
Proceed as explained in the previous "Direct Wa-
shing" paragraph (7.7.3) to also proceed with drying
the floor.
Never use the machine without the detergent solu-
tion: the floor might be damaged.
6.7.5. POST-SCRUBBING OPERATIONS
Cut off the supply of detergent.
Lift the brush unit and turn off the brush motor.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks (as de-
scribed in 7.4 and 7.5).
Empty and clean the tanks (see sections 7.4 and 7.5).
Turn off the machine using the key and remove it
from the control panel.
If necessary, charge the battery (see the relative section).
6.8.
SPECIFIC INSTRUCTIONS FOR THE USE OF
POWER MAINS AC 230V MODEL
The power mains AC 230V machine may be turned on
only if the voltage indicated on the tag corresponds
with the available voltage and that the electrical out-
let is grounded (earthed).
Do not damage the feed cable; do not crush or pull on it.
• ATTENTION Make sure that the power cable does
not come into contact with the rotary brushes.
• ATTENTION !!! - The power mains AC 230V ma-
chine has parts, which are connected to the cur-
rent; contact with these could cause grave injuries
or even death.
- Before executing any type of operation on the ma-
chine always disconnect it from the electrical source.
- Never touch electric cables that are defective or worn.
- Before gaining access to the electrical system it is
always necessary to disconnect the machine from
the electrical source by removing the plug from the
socket-outlet.
- In the case of defective, damaged, or cracked electric
cables, replace immediately with authentic replace-
ment parts.
- The network of connections must be protected from
water spray.
- The patch cord for the connection of the machine
to the mains power must conforms to current
safety rules.
- The electrical system to which the machine is con-
nected must be equipped with a cutout box.
- It is absolutely forbidden to use the machine in
proximity to swimming pools or stretches of water.
• EMERGENCY SITUATIONS
In case of emergency:
- Immediately disconnect the machine from the
power mains.
- Immediately apply proper first-aid.
If an accident should occur the machine must not be
put into operation until a technician authorized by
the manufacturer has examined it.
7.
MAINTENANCE INFORMATIONS
• Turn the key, remove it from the control panel and
disconnect the battery from the machine wiring.
☞ All work on the electrical system as well as all main-
tenance and repair operations (especially those not
explicitly described in this manual) should be carried
out only by authorised service centres or by speciali-
sed technical personnel who are experts in the sector
and in the pertinent safety regulations.
Performing regular maintenance on the machine,
and carefully following the manufacturer's instruc-
tions, is the best guarantee for obtaining the best
performances and extended machine service life.
7.1.
TANKS
Drain the two tanks as described in the relative sec-
tions.
Remove any solid dirt by filling and draining the
tanks until all dirt has been eliminated: use a washing
hose or similar tool to do this.
• Water hotter than 50°, a high-pressure cleaner
or excessively powerful sprays may damage the
tanks and the machine.
33
Werbung
Inhaltsverzeichnis
