Final Check - Beko BHCA66641BBHS Installationsanleitung

• If you are going to install it with a double
chimney, the measure from the required
clearance distance above the hob to your
furniture should be in the range of 910-
1138 mm. (Picture 4b)
• If you are going to install it with a single
chimney, the measure from the required
clearance distance above the hob to your
furniture should be 748 mm. (Picture 3a-
4a) For the installation with one chimney,
use the upper chimney which has
ventilation hole.
Assembling the product fixing parts
(Picture 5-6-7)
Your product is described over double
chimney sheet assembly sampling.
• Center your hob and draw a vertical axis
line on the wall.
• Draw a horizontal reference line measuring
650 mm from the top of your hob. (Picture 5)
• Center the template given with the product
on the reference point you have drawn,
paste it on the wall and mark the holes in
the template with a pencil. (Picture 6)
• Mark the holes for the chimney fixing
parts according to the dimensions given in
picture 6 from the top of your furniture or
ceiling.
• Fix the hood fixing part and chimney fixing
parts to the wall as shown in picture 7.
Hanging, aligning and fixing the hood
(Picture 8-9-10-11)
• Hang your hood on the hood fixing part
that you have fixed to the wall. (Picture 8)
• Align your hob in a central position by
sliding the hood left and right on the fixing
parts. (Picture 9)
• Open the glass cover of the hood and
remove the aluminum filter as shown in
picture 10.
• Fix your hood on the hood fixing part as
shown in picture 11 with the glass cover
open.
• Close the hood glass cover by fitting the
aluminum filter into its place.
• Fitting the chimney outlet pipe
(Picture 12)
• As shown in the picture 12, place the
cover that prevents reversed air flow to the
chimney outlet.
• If your chimney connection pipe's diameter
is 150 mm place the chimney outlet pipe
onto the cover
10
• If your chimney connection pipe's diameter
is 120 mm; Place the chimney outlet pipe
after placing the connection adapter on the
cover.
• Properly insulate the connection points.
Fixing the chimney sheets (Picture
13-14)
• If your chimney connection pipe's diameter
is 120 mm; Stick the supplied tape around
the junction of the connection adapter and
the air outlet slot. (Picture 13)
• Fix the upper chimney sheet to the upper
chimney fixing part with 2 screws from the
sides of the curves. (Picture 13)
• Fix the lower chimney sheet to the lower
chimney fixing part with 2 screws from the
curves on the sides. (Picture 14)
• Complete the installation by fixing the lower
chimney sheet with 2 screws from the
bottom hole circles on the hood. (Picture
14)

Final check

• Control your hood and lamp by operating it
as described in the user manual.
DE- Sicherheitshinweise
• Das Produkt muss von einer qualifizierten
Person in Übereinstimmung mit den
geltenden Vorschriften installiert werden.
Der Hersteller ist nicht verantwortlich für
Schäden, die durch von nicht autorisierten
Personen durchgeführte Verfahren
entstehen, die auch zum Erlöschen der
Garantie führen können.
• Die Vorbereitung des Standorts und der
Elektroinstallation für das Produkt liegt in
der Verantwortung des Kunden. Bevor Sie
den autorisierten Kundendienst anrufen,
vergewissern Sie sich, dass die elektrische
Installation geeignet ist. Wenn nicht, rufen
Sie einen qualifizierten Elektriker an, um die
erforderlichen Vorkehrungen zu treffen.
• Das Produkt muss in Übereinstimmung mit
allen örtlichen Elektrovorschriften installiert
werden.
• Entfernen Sie vor der Installation des
Produkts alle darin enthaltenen Materialien
und Dokumente und überprüfen Sie visuell,
ob das Produkt Mängel aufweist. Wenn ja,
lassen Sie es nicht installieren.
• Das Gerät ist schwer, Sie brauchen also
mindestens einen zusätzlichen Helfer
• Trennen Sie vor der Installation die
elektrischen Verbindungen im zu
installierenden Bereich.