Media Playback Via Usb Input; Usb Recording - Horizon 9-Serie Nutzerhandbuch

selection before starting to search asking whether you
want to perform cable network search. If you select Yes
and press OK you can select Network or set values
such as Frequency, Network ID and Search Step on
the next screen. If you select No and press OK or the
network search dialogue is not displayed you can set
Start Frequency, Stop Frequency and Search Step
on the next screen. When finished, highlight Next and
press OK button to continue.
Note: Searching duration will change depending on the
selected Search Step.
Satellite: If Satellite broadcast search option is turned
on, the TV will search for digital satellite broadcasts
after other initial settings are completed. Before
satellite search is performed some settings should
be made.
Depending on the model and the selected country
the next step may be the selection of the installation
type for satellite. You can select to start an operator
installation or a standard installation at this point. If you
want to perform an operator installation set the Install
Type as Operator and then set the Satellite Operator
according to your operator preference. Some of the
following steps may differ or be skipped depending on
the selected operator in this step. If you set the Install
Type as Standard, you can continue with regular
satellite installation and watch satellite channels.
Press OK to proceed.
M7 Operator Option
To start an M7 operator installation set the Install
Type as Operator when prompted and the Satellite
Operator as the related M7 operator. Then highlight
Preferred Scan option and set as Automatic
channel scan and press OK to start the automatic
search. These options can be preselected depending
on the language and country selections that you
made in the earlier steps of the first time installation
process. You may be asked to select HD/SD or
country specific channel list according to your M7
operator type. Select one and press OK to proceed.
Wait till the scan is finished. Now the list has been
installed.
While performing an M7 operator installation, if you
want to use the satellite installation parameters that
differ from the default settings select the Preferred
Scan option as Manual channel scan and press the
OK button to proceed. Antenna type selection screen
will be displayed next. After selecting the antenna
type and the desired satellite in the following steps
press OK in order to change the satellite installation
parameters in the sub-menu.
Antenna type selection screen may be displayed
next. You can select Antenna type as Direct, Single
Satellite Cable or DiSEqC switch by using Left or
Right directional buttons. After selecting your antenna
type press OK to see the options to proceed. Continue,
Transponder list and Configure LNB options may be
available. You can change the transponder and LNB
settings using the related menu options.
Direct: If you have a single receiver and a direct
satellite dish, select this antenna type. Press OK to
continue. Select an available satellite on the next
screen and press OK to scan for services.
Single Satellite Cable: If you have multiple receivers
and a single satellite cable system, select this anten-
na type. Press OK to continue. Configure settings
by following instructions on the next screen. Press
OK to scan for services.
DiSEqC switch: If you have multiple satellite dishes
and a DiSEqC switch, select this antenna type. Then
set the DiSEqC version and press OK to continue.
You can set up to four satellites (if available) for
version v1.0 and sixteen satellites for version v1.1
on the next screen. Press OK button to scan the first
satellite in the list.
Note: Depending on the model of your TV, DiSEqC version
v1.1 may not be supported and therefore the DiSEqC version
selection step may not be available.
Analogue: If Analogue broadcast search option is
turned on, the TV will search for analogue broadcasts
after other initial settings are completed.
After the initial settings are completed the TV will start
to search for available broadcasts of the selected
broadcast types.
While the search continues current scan results will be
displayed at the bottom of the screen. You can press
the Home, Back or Exit button to cancel the search.
The channels that have already been found will be
stored in the channel list.
After all the available stations are stored, Channels
menu will be displayed. You can edit the channel
list according to your preferences using the Edit tab
options or press the Home button to quit and watch TV.
While the search continues a dialogue may appear,
asking whether you want to sort channels according
to the LCN(*). Select Yes and press OK to confirm.
(*) LCN is the Logical Channel Number system that organises
available broadcasts in accordance with a recognisable
channel number sequence (if available).
Notes:
To search for M7 channels after the First Time Installation,
you should perform the first time installation again. Or press the
Home button and enter the Settings>Installation>Automatic
channel scan>Satellite menu. Then follow the same steps
mentioned abow in the satellite section.
Do not turn off the TV while initialising first time installation.
Note that, some options may not be available depending on
the country selection.
English - 14 -

Media Playback via USB Input

You can connect 2.5" and 3.5" inch (HDD with external power
supply) external hard disk drives or USB memory stick to your
TV by using the USB input(s) of the TV.
IMPORTANT! Back up the files on your storage devices
before connecting them to the TV. Manufacturer will
not be responsible for any file damage or data loss.
Certain types of USB devices (e.g. MP3 Players)
or USB hard disk drives/memory sticks may not be
compatible with this TV. The TV supports FAT32 and
NTFS disk formatting but recording will not be available
with NTFS formatted disks.
While formatting USB hard drives which have
more than 1TB (Tera Byte) storage space you may
experience some problems in the formatting process.
Wait a little while before each plugging and unplugging
as the player may still be reading files. Failure to do
so may cause physical damage to the USB player
and the USB device itself. Do not pull out your drive
while playing a file.
You can use USB hubs with your TV's USB input(s).
External power supplied USB hubs are recommended
in such a case.
It is recommended to use the TV's USB input(s)
directly, if you are going to connect a USB hard disk.
Note: When viewing media files the Media Browser menu
can only display a maximum of 1000 media files per folder.

USB Recording

Recording a Programme
IMPORTANT: When using a new USB hard disk
drive, it is recommended that you first format the
disk using your TV's Format Disk option in the
TV>Recordings>Settings menu.
To record a programme, you should first connect a USB
disk to your TV while the TV is switched off. You should
then switch on the TV to enable the recording feature.
To use recording your USB drive should have 2 GB free
space and be USB 2.0 compatible. If the USB drive
is not compatible an error message will be displayed.
To record long duration programmes such as movies, it
is recommended to use USB Hard disk drives (HDD's).
Recorded programmes are saved onto the connected
USB disk. If desired, you can store/copy recordings
onto a computer; however, these files will not be
available to be played on a computer. You can play
the recordings only via your TV.
Lip Sync delay may occur during timeshifting. Radio
record is supported. The TV can record programmes
up to ten hours.
Recorded programmes are split into 4GB partitions.
If the writing speed of the connected USB disk is not
sufficient, the recording may fail and the timeshifting
feature may not be available.
It is recommended to use USB hard disk drives for
recording HD programmes.
Do not pull out the USB/HDD during a recording. This
may harm the connected USB/HDD.
Multipartition support is available. A maximum of two
different partitions are supported. The first partition
of the USB disk is used for USB Recording ready
features. It also must be formatted as the primary
partition to be used for the USB Recording ready
features.
Some stream packets may not be recorded because
of signal problems, as a result sometimes videos may
freeze during playback.
While recording a programme in the background you
can use menu options, switch to another source or use
Media Browser functions, such as viewing pictures,
playing video and music files, and even play back the
ongoing recording.
Timeshift Recording
Press Pause button while watching a broadcast to
activate timeshifting mode. In timeshifting mode, the
programme is paused and simultaneously recorded to
the connected USB disk.
Press Pause button again or Play button to resume
the paused programme from where you stopped. Press
the Stop button to stop timeshift recording and return
to the live broadcast.
Timeshift cannot be used while in radio mode.
You can use the timeshift rewind feature after resuming
normal playback or fast forward option.
Instant Recording
Press Record button to start recording an event
instantly while watching a programme. Press Stop
button to cancel instant recording.
You can not switch broadcasts during the recording
mode. While recording a programme or during
timeshifting, a warning message appears on the screen
if your USB device speed is not sufficient.
Watching Recorded Programmes
Select Recordings from the TV menu. Select a
recorded item from the list (if previously recorded).
Press the OK button to view the Options menu. Select
an option then press OK button.
Note: Viewing main menu and menu items will not be available
during the playback.
Press the Stop button to stop a playback and return
to the Recordings.
Slow Forward / Slow Rewind
If you press Pause button while watching recorded
programmes, the slow forward and slow rewind
functions will be available. You can use Fast Forward
button to slow forward and Rewind button to slow
rewind. Pressing the button consecutively will change
slow forwarding and slow rewinding speed.
English - 15 -