Assembly / Before Commissioning; Start Up; Cleaning; Storage - Scheppach DC100 Originalbetriebsanleitung

• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
m ATTENTION!
The device and the packaging material are not
children's toys! Do not let children play with
plastic bags, films or small parts! There is a dan-
ger of choking or suffocating!

8. Assembly / Before commissioning

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Installing the filter cartridge (10) with filter bag
(11), Fig. 3 - 5
• Insert the filter cartridge (10) into the filter bag (11).
(Fig. 3 + 4)
• Press the overhang into the filter cartridge (10).
(Fig. 4)
• Now fit the filter cartridge (10) on the engine hous-
ing (1). (Fig. 5)
• Place the complete engine housing (1) on the con-
tainer (3) and lock the locking hooks (9).
Installing the suction hose (5), Fig. 6 + 7
• Fit the suction hose (5) with the hose clamp (8) on
the hose port of the container (3).
• Fit the other side of the suction hose (5) with the
hose clamp (8) and hose coupling (7).

9. Start up

m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
Switching on/off, Fig. 1
• To switch on, set the ON/OFF switch (4) to position
"I".
• To switch the device off again, set the ON/OFF
switch (4) to position "0".
Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
Damaged electrical connection cable
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables of the same designation.
The printing of the type designation on the connec-
tion cable is mandatory.
For single-phase AC motors, we recommend a fuse
rating of C 16A or K 16A for machines with a high
starting current (from 3000 watts)!

10. Cleaning

Attention!
Disconnect the mains plug before carrying out any
cleaning work.
We recommend that you clean the device directly af-
ter every use.
Wipe swarf and dust off the machine from time to time
with a cloth.
Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can pen-
etrate the device interior.

11. Storage

Store the device and its accessories in a dark, dry
and frost-free place that is inaccessible to children.
The optimum storage temperature lies between 5 and
30 ˚C.
Store the tool in its original packaging.