Introduction; Device Description; Scope Of Delivery; Proper Use - Scheppach DC100 Originalbetriebsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer
We hope your new tool brings you much enjoyment
and success.
Note:
In accordance with the applicable product liability
laws, the manufacturer of this device assumes no
liability for damage to the device or caused by the
device arising from:
• Improper handling
• Failure to comply with the operating instructions.
• Repairs carried out by third parties, unauthorised
specialists
• Installing and replacing non-original spare parts,
• Improper use
• Failures of the electrical system in the event of the
electrical regulations and VDE provisions 0100,
DIN 57113 / VDE 0113 not being observed
Note:
Read the whole text of the operating manual before
assembly and commissioning.
This operating manual should help you to familiarise
yourself with your device and to use it for its intended
purpose.
The operating manual includes important instructions
for safe, proper and economic operation of the de-
vice, for avoiding danger, for minimising repair costs
and downtimes, and for increasing the reliability and
extending the service life of the device.
In addition to the safety instructions in this operating
manual, you must also observe the regulations appli-
cable to the operation of the device in your country.
Keep the operating manual at the device, in a plastic
sleeve, protected from dirt and moisture. They must
be read and carefully observed by all operating per-
sonnel before starting the work.
The device may only be used by personnel who have
been trained to use it and who have been instructed
with respect to the associated hazards. The required
minimum age must be observed.
In addition to the safety instructions in this operating
manual and the separate regulations of your coun-
try, the generally recognised technical rules relating
to the operation of such machines must also be ob-
served.
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

2. Device description

1. Engine housing
2. Handle
3. Chip container
4. On/off switch
5. Suction hose
6. Adapter
7. Hose coupling
8. Hose clamp
9. Locking hooks
10. Filter cartridge
11. Filter bag
12. Hose coupling Ø100mm

3. Scope of delivery

• Suction system
• Suction hose
• Hose coupling
• Adapter set (4-piece)
• Filter cartridge
• Filter bag
• 2x hose clamp
• Hose coupling Ø100mm
• Operating manual

4. Proper use

The machine complies with the applicable EC ma-
chinery directive.
• The machine has been built according to the state-
of-the-art and the technical safety requirements.
Nevertheless, its use may cause danger to the life
and limb of the user or third parties, or damage to
the machine and other material assets.
• Only use the machine when in a technically fault-
less condition, appropriately and in compliance
with the operating manual and with full knowledge
of safety and hazards! In particular, rectify malfunc-
tions that could impair safety immediately (or com-
mission rectification works accordingly)!
• The suction system is used for extracting chips
which are produced when working with wood or
wood-like materials.
• Please observe that our equipment was not de-
signed with the intention of use for commercial or
industrial purposes. We assume no guarantee if
the equipment is used in commercial or industrial
applications, or for equivalent work.
• Check the filter regularly for damage. Replace
damaged filters! Regularly check the housing seal
and the seals for the filter and dust bag.
• When using the cleaning nozzles, do not suck up
any foreign bodies such as screws, nails, pieces of
plastic or wood.
GB | 15