Adler europe AD 4221 Bedienungsanweisung Seite 6

unplug the power cable.
18. Before operating the device check if all parts and accessories are properly mounted:
- planetary food processor: ensure the attachment is fully inserted into the socket,
otherwise your mixing result may be affected.
- meat grinder: the grinding assembly needs to be carefully assembled. Inaccurate
assembly can cause poor grinding performance and knife and hole plate blunting.
19. Use only original accessories supplied with the meat grinder and planetary food
processor.
20. Do not overload the device with excess product or shoving the product in too hard. Use
only the pusher for shoving the product in. Using other object can damage the meat
grinder.
22. The meat to be ground should be free of bones, gristles, tendons or veins. Cut the
bigger parts into pieces.
23. Do not cover the ventilation holes in the housing while the device is on.
24. Do not grind dry poppy seed. The poppy seed needs to be steamed and soaked before
grinding.
25. Do not exceed ¾ bowl high when fill up by food ingredients.
26. Store the device out of the reach of children.
Product description: Multifunction Planetary food processor AD4221
1.Housing arm
3.Anti-splash cover
5.Front cover of mincer
7.Tilt knob
9.Egg whisk
11.Dough hook
13.Sieves 3, 5 ,7mm
15.Worm gear
17. Mincing chamber
BEFORE FIRST USING
1. All parts of the device are to be thoroughly cleaned before being used for the first time. See section: "Cleaning and Maintenance".
2. Stand the device on a horizontal and flat surface.
3. Never operate the device without the supervision.
4. Do not touch moving parts with your fingers. Let the rotating accessories to stop before open the bowl.
WARNING: DO NOT USE MIXING AND MINCING FUNCTIONS AT THE SAME TIME !! ONLY USE ONE OF THEM.
• When using mixing function the front cover (5) should be located at its position.
• When using mincing function the bowl (4) with anti-splash cover (3) should be located at their position to protect end user against
rotation of the mixer's attachment nest with spring (18).
5. Switch off the device and disconnect from supply before changing accessories.
ASSEMBLY WAY: Mixer function
Before assembling the food processor, be sure the power cord unplugged from the power outlet and the speed control knob is on the "0"
position.
1.Place the bowl in the motor unit, then turn it clockwise until you feel it cannot move any further to the left. The bowl is blocked.
2.Choose proper attachment to required operation:
- Egg whisk (9) for whipping :egg whites, cake creams, whipped cream, etc.
- Mixing beater (10) for mixing light mixtures: mayonnaise, pancake batter , sponge cake, etc.
- Dough hook (11) for kneading heavy dough: bread dough, yeast dough, etc.
3. Put the proper attachment (9 or 10 or 11) on the bolt of the mixer's attachment nest with spring (18). Adjust the position of two protrude
metal elements to come inside concave places of the mixer 's attachment nest with spring (18) – look at picture A. Push the
attachment upwards until the spring is fully compressed, turn fully clockwise and release – look at picture B.
4. Put food ingredients into the bowl and press the tilt knob (7) down side to close the housing arm (1).
5. Plug in the device and rotate the speed knob (8) for required speed. The speed 0 means motor stopped, the speed 1 means slowest
speed, the speed 6 means maximum rotation. P – means Pulse mode, it means pulse rotating of gears when the knob (8) is kept at
Pulse position.
6. After use switch off the device by rotate the speed knob (8) to position 0 and plug of f the device.
7. Press the tilt knob (7) down side to lift the housing arm (1). If mixed mixture is correct, take away the attachment. To take away the
attachment, lift it a little to compress the spring completely , then turn left side whole attachment and pull it down.
8. Turn the bowl (4) counterclockwise and remove it from the motor housing (2) by keeping with both hands. Remember the bowl can be
heavy.
2. Motor housing
4.Mixing bowl 7,0 liters
6.Plastic pusher
8.Speed control knob
10.Mixing beater
12.Fixing nut
14.Mincing cross blade
16. Mincing tray
18.Mixer's attachment nest with spring
6