Operation; Fuse Replacement; Technical Data - Renkforce T-900B Bedienungsanleitung

Operation

(1) PHONE for the connection of a headset
(2) AV IN for the connection of external AV devices
(3) MODE toggles the display format (4:3/16:9)
(4) V1/V2 switches the video input (VIDEO 1 IN/VIDEO 2 IN)
(5) "-" turns the volume down or changes settings in the menu
(6) M is used to access the menu – the menu points are accessed by pressing several times, settings are
performed via the "-" and "+" keys
BRIGHTNESS brightness adjustment
CONTRAST contrast adjustment
SATURATION
saturation adjustment
VOLUME volume adjustment
SOURCE selection of the input: VIDEO 1 IN/VIDEO 2 IN
RESET restore of factory settings
L/R mirroring of the display
U/D rotation of the display
16:9/4:3 switching of the display format
EXIT exiting the menu
(7) "+" turns the volume up or changes the settings in the menu
(8) POWER switches the monitor on/off
(9) Infrared receiver for the remote control
(10) Power indicator - lights up when the device is turned on
(1) MUTE – switches the sound on/off
(2) MD toggles the display format (4:3/16:9)
(3) L/R mirrors the display (e.g. for use of a reversing camera)
(4) U/D rotates the display by 180° (if the monitor has been hung up)
(5) AV switches the video input (VIDEO 1 IN/VIDEO 2 IN)
(6) ON/OFF switches the monitor on/off
(7) Adjustment of the display brightness
(8) Adjustment of the display contrast
(9) Adjustment of the saturation of the display
(10) Adjustment of the volume
All manuals and user guides at all-guides.com

Fuse replacement

If it becomes necessary to replace a fuse, make sure that only fuses of the prescribed type and nominal
current are used (see "Technical Data").
• Disconnect the monitor from the power supply.
• Unscrew the fuse holder in the red connection.
• Remove the defective fuse and replace it with a fuse of the same type.
• Close the fuse holder again.
• Only then the monitor should be re-connected to the car system and put into operation.
• Should the fuse trigger again, have the device repaired in a specialist workshop.
Disposal
a) Product
b) Batteries and Rechargeable Batteries
The end user is legally obliged (Battery Regulation) to return used batteries and rechargeable batteries. Do
not dispose of used batteries in the household waste!
You can return used batteries/rechargeable batteries free of charge to any collecting point in your local com-
munity, in our stores or in any other store where batteries/rechargeable batteries are sold.
You thereby fulfi l your statutory obligations and contribute to the protection of the environment.

Technical Data

Operating voltage ..........................................12 V/DC
Power consumption .......................................500 mA
Battery for remote control ..............................3 V lithium button cell CR2025
Fuse ...............................................................T2AL/250V (5 x 20 mm)
Display size ...................................................22.9 cm (9")
Display format ................................................16:9
Defi nition ........................................................800 x 480
TV format .......................................................PAL/NTSC
Dimensions (without mounting frame) ...........226 x 157 x 30 mm
Installation opening ........................................163 x 232 mm
Mounting depth ..............................................24 mm
Range of operating temperature ....................0 – 50 °C
Weight ...........................................................490 g
You must not carry out your own repairs to fuses or bridge the fuse holder.
Electronic devices are recyclable waste materials and must not be disposed of in the household
waste!
Please dispose of the product, when it is no longer of use, according to the current statutory
requirements.
Remove the battery in the remote control and dispose of it separately from the product.
Contaminated batteries/rechargeable batteries are labelled with these symbols to indicate that
disposal in the domestic waste is forbidden. The symbols for the relevant heavy metals are:
Cd=Cadmium, Hg=Mercury, Pb=Lead (marking can be seen on the battery/rechargeable bat-
tery, e.g., underneath the rubbish bin symbol shown on the left).
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.