Herunterladen Inhalt Inhalt Diese Seite drucken

Storage; Storage Safety; Cleaning And Storage - Toro Titan X4850 Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für Titan X4850:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Storage

Storage Safety

Shut off the engine, remove the key, and wait
for all moving parts to stop before you leave the
operator's position. Allow the machine to cool
before adjusting, servicing, cleaning, or storing it.
Do not store the machine or fuel near flames or
drain the fuel indoors or inside an enclosed trailer.
Do not store the machine or fuel container where
there is an open flame, spark, or pilot light, such
as on a water heater or on other appliances.

Cleaning and Storage

1.
Disengage the blade-control switch (PTO), and
engage the parking brake.
2.
Shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operating position.
3.
Remove grass clippings, dirt, and grime from the
external parts of the entire machine, especially
the engine and hydraulic system. Clean dirt and
chaff from the outside of the engine cylinder
head fins and blower housing.
Important:
You can wash the machine
with mild detergent and water. Do not
pressure-wash the machine. Avoid
excessive use of water, especially near the
control panel, engine, hydraulic pumps, and
motors.
4.
Check the parking brake operation; refer to
Operating the Parking Brake (page
5.
Service the air cleaner; refer to
Cleaner (page
34).
6.
Change the crankcase oil; refer to
Engine Oil and Oil Filter (page
7.
Check the tire pressure; refer to
Tire Pressure (page
8.
Charge the battery; refer to
(page
42).
9.
Scrape any heavy buildup of grass and dirt
from the underside of the mower, then wash the
machine with a garden hose.
Note:
Run the machine with the blade-control
switch (PTO) engaged and the engine at high
idle for 2 to 5 minutes after washing.
10.
Check the condition of the blades; refer to
Servicing the Cutting Blades (page
11.
Prepare the machine for storage when non-use
occurs over 30 days. Prepare the machine for
storage as follows:
23).
Servicing the Air
Changing the
37).
Checking the
43).
Charging the Battery
44).
A.
Add fuel stabilizer/conditioner to fresh fuel
in the tank. Follow mixing instructions from
the fuel stabilizer manufacturer. Do not
use an alcohol-based stabilizer (ethanol or
methanol).
B.
Run the engine to distribute conditioned fuel
through the fuel system for 5 minutes.
C.
Shut off the engine, allow it to cool, and
drain the fuel tank.
D.
Start the engine and run it until it shuts off.
E.
Dispose of fuel properly. Recycle the fuel
according to local codes.
Important:
stabilizer/conditioner longer than
the duration recommended by the
fuel-stabilizer manufacturer.
12.
Remove and check the condition of the spark
plug(s); refer to
38). With the spark plug(s) removed from the
engine, pour 30 ml (2 tablespoons) of engine
oil into the spark plug hole. Use the starter to
crank the engine and distribute the oil inside the
cylinder. Install the spark plug(s). Do not install
the wire on the spark plug(s).
13.
Check and tighten all bolts, nuts, and screws.
Repair or replace any part that is damaged.
14.
Paint all scratched or bare metal surfaces. Paint
is available from your Authorized Service Dealer.
15.
Store the machine in a clean, dry garage or
storage area. Remove the key from the switch
and keep it out of reach of children or other
unauthorized users. Cover the machine to
protect it and keep it clean.
52
Do not store fuel containing
Servicing the Spark Plug (page

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis