Makita SA5040C Bedienungsanleitung Seite 11

For tool with clamp lever type wheel
guard
► Fig.13: 1. Wheel guard 2. Bearing box 3. Screw
4. Lever
Pull the lever in the direction of the arrow after loosen-
ing the screw. Mount the wheel guard with the protru-
sions on the wheel guard band aligned with the notches
on the bearing box. Then rotate the wheel guard around
180°.
► Fig.14: 1. Screw 2. Lever
Tighten the wheel guard with fastening the screw after
pulling lever in the direction of the arrow. The setting
angle of the wheel guard can be adjusted with the lever.
To remove wheel guard, follow the installation proce-
dure in reverse.
Installing or removing depressed
center wheel or flap disc (optional
accessory)
WARNING:
• When using a depressed center wheel or flap
disc, the wheel guard must be fitted on the tool
so that the closed side of the guard always
points toward the operator.
► Fig.15: 1. Lock nut 2. Depressed center wheel
3. Inner flange
Mount the inner flange onto the spindle. Fit the wheel/
disc on the inner flange and screw the lock nut onto the
spindle.
► Fig.16: 1. Lock nut wrench 2. Shaft lock
To tighten the lock nut, press the shaft lock firmly so
that the spindle cannot revolve, then use the lock nut
wrench and securely tighten clockwise.
To remove the wheel, follow the installation procedure
in reverse.
Super flange (Optional accessory)
Models with the letter F are standard-equipped with
Super flange. Only 1/3 of efforts needed to undo lock
nut, compared with conventional type.
CAUTION:
• Do not use super flange for models equipped
with the mechanical brake. Otherwise it may
loosen when the brake is activated.
Installing or removing Ezynut
(optional accessory)
CAUTION:
• Do not use Ezynut with Super Flange or angle
grinder with "F" on the end of the model No.
Those flanges are so thick that the entire thread
cannot be retained by the spindle.
► Fig.17: 1. Ezynut 2. Abrasive wheel 3. Inner flange
4. Spindle
Mount inner flange, abrasive wheel and Ezynut onto the
spindle so that Makita Logo on Ezynut faces outside.
► Fig.18: 1. Shaft lock
Press shaft lock firmly and tighten Ezynut by turning the
abrasive wheel clockwise as far as it turns.
Turn the outside ring of Ezynut counterclockwise to
loosen.
► Fig.19: 1. Arrow 2. Notch
► Fig.20
NOTE:
• Ezynut can be loosened by hand as long as
the arrow points the notch. Otherwise a lock
nut wrench is required to loosen it. Insert one
pin of the wrench into a hole and turn Ezynut
counterclockwise.
Installing or removing flex wheel
(optional accessory)
WARNING:
• Always use supplied guard when flex wheel is
on tool. Wheel can shatter during use and guard
helps to reduce chances of personal injury.
► Fig.21: 1. Lock nut 2. Flex wheel 3. Plastic pad
4. Inner flange
Follow instructions for depressed center wheel but also
use plastic pad over wheel. See order of assembly on
accessories page in this manual.
Installing or removing abrasive disc
(optional accessory)
NOTE:
• Use sander accessories specified in this man-
ual. These must be purchased separately.
► Fig.22: 1. Sanding lock nut 2. Abrasive disc
3. Rubber pad
Mount the rubber pad onto the spindle. Fit the disc on
the rubber pad and screw the sanding lock nut onto the
spindle. To tighten the sanding lock nut, press the shaft
lock firmly so that the spindle cannot revolve, then use
the lock nut wrench and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse.
Installing or removing dust cover
attachment (Optional accessory)
WARNING:
• Always be sure that the tool is switched off
and unplugged before installing or removing
the dust cover attachment. Failure to do so
causes damage to the tool or a personal injury.
There are four pieces of dust cover attachment and
each is used in one of different positions.
► Fig.23: 1. Marking A 2. Marking B 3. Marking C
4. Marking D
Set the dust cover attachment so that the marking (A, B,
C or D) places as shown. Snap its pins in the vents.
Dust cover attachment can be removed by hand.
11 ENGLISH