Makita LS0714 Bedienungsanleitung Seite 21

EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to 33.9°
LEFT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its CEILING
CONTACT EDGE against the guide fence on
the saw.
• The finished piece to be used will always be
on the LEFT side of the blade after the cut has
been made.
In the case of right bevel cut
Table (A)
Bevel angle
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Right 33.9° Right 30°
(3)
For outside
corner
(4)
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Wall contact edge should be
(1)
against guide fence.
For inside
corner
(2)
Ceiling contact edge should
be against guide fence.
For
(3)
outside
corner
Wall contact edge should be
(4)
against guide fence.
EXAMPLE In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
• Tilt and secure bevel angle setting to 33.9°
RIGHT.
• Adjust and secure miter angle setting to 31.6°
RIGHT.
• Lay crown molding with its broad back (hidden)
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on
the saw.
• The finished piece to be used will always be on
the RIGHT side of the blade after the cut has
been made.
Cutting aluminum extrusion
► Fig.48: 1. Vise 2. Spacer block 3. Guide fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in the figure to prevent
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the blade.
Miter angle
45° type 52/38° type 45° type
Right 31.6° Right 35.3°
Left 31.6° Left 35.3°
Right 31.6° Right 35.3°
Finished piece
Finished piece
will be on the
Right side of
blade.
Finished piece
will be on the
Left side of
blade.
CAUTION:
• Never attempt to cut thick or round aluminum
extrusions. Thick aluminum extrusions may
come loose during operation and round alumi-
num extrusions cannot be secured firmly with
this tool.
Wood facing
Use of wood facing helps to assure splinter-free cuts
in workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence.
See the figure concerning the dimensions for a sug-
gested wood facing.
Over 15mm (5/8")
35mm
(1-3/8")
92mm
1
(3-5/8")
1. Holes
CAUTION:
• Use straight wood of even thickness as the
wood facing.
• Use screws to attach the wood facing to the
guide fence. The screws should be installed so
that the screw heads are below the surface of
the wood facing.
• When the wood facing is attached, do not turn
the turn base with the handle lowered. The
blade and/or the wood facing will be damaged.
Cutting repetitive lengths
CAUTION:
For the tool equipped with the hold-
ers and the holder assemblies as standard acces-
sories, this type of use is not permitted due to the
country regulations.
► Fig.49: 1. Set plate 2. Holder 3. Screw
When cutting several pieces of stock to the same
length, ranging from 220 mm to 385 mm, use of the set
plate (optional accessory) will facilitate more efficient
operation. Install the set plate on the holder (optional
accessory) as shown in the figure.
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and
while holding the workpiece from moving, move the
set plate flush against the end of the workpiece. Then
secure the set plate with the screw. When the set plate
is not used, loosen the screw and turn the set plate out
of the way.
NOTE:
• Use of the holder-rod assembly (optional acces-
sory) allows cutting repetitive lengths up to
2,200 mm approximately.
21 ENGLISH
Over 420mm (16-1/2")
27mm (1-1/16")
100mm 70mm 85mm
(3-15/16") (2-3/4")
(3-3/8")
50mm-60mm
(2"-2-3/8")
1