Troubleshooting - Clarion EE-2178E Installations- Und Bedienungsanleitung

HOW TO INSTALL
● ■ How to attach the receiver
Precautions for attachment Precautions for attachment
• Be sure to use the specified screws when attaching the
receiver. Use of other screws may result in malfunction.
1
Please install the receiver at stable position according to the
following diagram.
! Antenna
Rotate the threaded portion of the antenna clockwise and fix
the antenna securely to the receiver to prevent loosening.
7 Self tapping screws
( 5 mm x 16 mm)
(Four places)
6 Hexagon head bolts
with built-in washer
(M5 mm x 8 mm)
(Four places)
45 mm
5 Mounting brackets
(Tow places)
● ■ How to mount the camera with transmitter
CAUTION
● Never swing the camera by the cable or pull the cable. Doing
●
so may impair the camera's watertightness or break the cable,
resulting in malfunction.
● Avoid mounting the camera where the lens will be exposed to
●
dirt (mud splashes, exhaust fumes, etc.).
● To prevent the camera from shaking, make sure the camera is
●
mounted to solid surface. The surface may need reinforcement if
it is not solid and secure.
● Be sure to use the supplied screws to mount the camera. If
●
any screws are lost when mounting the camera, be sure to use
hexagon head bolts with built-in washer (M3 mm x 8 mm). Do
not under any circumstances use screws longer than this. To
ensure watertightness, the screw mounting holes in the camera
case have a bag structure. Use of long screws may damage the
screw thread and camera case, compromising watertightness.
1
Make a hole (2 places) for mounting the bracket in the
chassis and fix the bracket securely with the $ hexagon
head bolts with built-in washer and flanged nuts.
2
Push-fit the gasket boss (2 places) into the guide hole from
inside the bracket.
3
Temporarily fix the camera in 4 places (a) with the
# hexagon head bolts with built-in washer.
4
Using tools such as needle nose pliers, rotate the threaded
portion of the antenna clockwise and fix the antenna
securely to the camera to prevent loosening.
5
Temporarily fix the antenna bracket in 1 place (b) with the
# hexagon head bolt with built-in washer so that the angle
of the antenna is controlled.
6
Install the wiring. (Refer to WIRING AND CONNECTIONS)
7
Adjust the mounting angle of the camera so that the rear
bumper or back end of the vehicle appears in the monitor
and tighten the bolts (a) to fix securely. (See diagram below)
Monitor screen
The recommended guideline is approximately
1/10 of the monitor's overall height.
Rear bumper or rear end of the vehicle
8
Adjust the antenna angle for optimal signal reception and
tighten the bolt (b) to fix securely.
0 Mounting bracket
Vehicle side : 5.5 mm holes (Two places)
% Flanged nuts (M5 mm) (Two places)
PAIRING
When using the camera for the first time, pairing of the camera and the receiver is required. The pairing shall be done according to
the procedures below.
If the connected camera is replaced after pairing, the pairing procedure in Step 2 changes. The procedure is shown in the Advice
column.
● ■ Pairing Switch Operation
•Short-press the pairing switch  The cursor will move on the screen.
•Press and hold the pairing switch button for at least 3 seconds  Enter, or the pairing will start
1
Turn on the power.
➞ The [Clarion] welcoming
●
screen appears and then
the screen changes in
sequence.
2
When the [Connecting]
screen appears, press and
hold the pairing switch for at
least 3 seconds.
➞ The [Searching for the
●
pairing device] screen
appears.
The receiver is searching
for a camera to pair. When
the search is completed,
the pairing selection
screen appears.
3
Short-press the pairing
switch to point the cursor
The camera you want to
to the camera number you pair appears on the pairing
selection screen
want to pair and press the
pairing switch for at least 3
seconds.
➞ The selected camera
●
is connected and the
camera screen appears.
Advice Advice
• If the camera you want to pair does not appear
on the pairing selection screen or if the pairing
selection screen is not displayed, follow the steps
on the right to repeat the search.
• If multiple camera numbers appear and you do
not know which to choose, select each number
in turn to find the right one.
4
If there is no problem with
the displayed camera
image, short-press the
pairing switch to point the
cursor to [Connect] and
press the pairing switch for
at least 3 seconds.
➞ [Connect] disappears
●
from the screen and
only the camera image
is displayed. Pairing is
completed.
@ Gaskets (Two places)
¥ Antenna bracket
# Hexagon head
bolts with built-in
washer (a)
(M3 mm x 8 mm)
(Four places)
Boss
Boss
! Antenna
(a)
(a)
(a)
Threaded portion
(a)
of the antenna
# Hexagon head
bolt with built-in
(b)
washer (b)
Guide holes (M3 mm x 8 mm)
(One place)
$ Hexagon head bolts with
built-in washer (M5 mm x
8 mm) (Two places)
Advice Advice
• You cannot pair an already paired camera with another receiver.
• Once paired, the pairing information is saved when the power is
turned off.
• If repeated searching fails to find the device you want to pair, it may
be due to poor radio wave reception. Replace the antenna on the
receiver with the optional long antenna and try again.
• If the connected camera is replaced after pairing, Step 2 changes to
the following procedure.
1 Turn on the replacement camera and connect the antenna.
2 Press the pairing switch while the camera image is displayed.
➞ The [Pairing changeover] screen appears.
3 Press and hold the pairing switch for at least 3 seconds while the
[Pairing changeover] screen is displayed.
➞ The pairing selection screen appears.
The camera you want to The pairing selection
pair does not appear on screen is not displayed.
the pairing selection screen (No compatible camera
was found)
● ■ Repeat Search
➞Check that the camera is turned on and
●
the antenna is connected. Point the cursor
to [ Search again ] and press the pairing
switch for at least 3 seconds.
➞Searching starts again.
●
Advice Advice
• If a different screen is displayed, short-press the pairing
switch to point the cursor to [Cancel] and press the pairing
switch for at least 3 seconds.
➞Searching starts again and the search screen appears.
Wiring Precaution Wiring Precaution
• Please carry out waterproof treatment on hookup point
between camera power cable and vehicle wiring as per
the illustration below.
Camera power cable
Vehicle wiring
Waterproof Waterproof
The end of
camera power cable
Wire connections
As well as wire connections, please do waterproof to
the end of camera power cable.
WIRING AND CONNECTIONS
• When the power cable (red) of the camera/transmitter is connected to the ACC line, connect the
orange/white cable from the receiver to the ACC line along with the ACC signal (red).
• If there is no ACC power for the transmitter, connect the camera/transmitter's red cable to the
parking light line. At the same time, be sure to connect the orange/white cable from the receiver to
the parking light line. In this case, the camera image is displayed only when the driver turns on the
illumination.
• To prevent short-circuiting, check the connections again before connecting the battery.
Receiver
Camera
(EE-2178)
with transmitter
(CC-3500)
Pairing
switch
Brown Black
ACC+ / Parking light+
Connect to the positive power supply that can be turned on and off
with the ignition key, or to the parking light line+.
NOTE: When you connect the red cable to the Parking light lne,
the parking lights would need to be on in order for the camera to
work and the camera image will be ready to display all the time.
Ground (Negative)
Connect to chassis groud.
This wire is not used.
External monitor
(sold separately)
Red
ACC+
Example of monitor
Connect to a positive power supply that can be turned on and
combination
Orange
off with the ignition key.
with white stripe
Camera connection confirmation cable
Connect to a positive power supply where the camera red wire
Purple
is connected.
with white stripe
Reverse+
Connect to the reverse line which will have +12V/24V while in
reverse gear.
NOTE: Please connect to ACC line in order for the camera
image will be ready to display all the time.
Black
Ground (Negative)
Connect to chassis ground.

TROUBLESHOOTING

The following situations may not be malfunctions, please check prior to requesting service.
Symptom Cause
There is no image (Nothing appears The receiver is not connected Check the receiver's connections and connect the receiver
on the monitor) correctly correctly
There is no image ("Connecting..." is The camera is not connected correctly Check the camera's connections and connect the camera
continuously displayed on the monitor) correctly
The surrounding radio wave signal Move to a different place and check if the image appears
strength is weak
The radio wave reception of the Change the position of the antenna on the receiver or replace with the
camera is poor optional long antenna and check again.
There is no paired camera around Press the pairing switch for at least 3 seconds to complete pairing.
The image cuts out ("The video has The surrounding radio wave signal Move to a different place and check if the image appears
been stopped" appears) strength is weak
The radio wave reception of the Change the position of the antenna on the receiver or replace with the
camera is poor optional long antenna and check again.
"Communication has been The camera has been disconnected Depending on the state of the surrounding radio waves, the
disconnected." appears on the camera is disconnected. Reconnection is automatic.
monitor
The camera you want to pair does not The camera is not connected correctly Check the camera's connections and connect the camera
appear on the pairing selection screen correctly
The surrounding radio wave signal Move to a different place and check if the image appears
strength is weak
The radio wave reception of the Change the position of the antenna on the receiver or replace with the
camera is poor optional long antenna and check again.
The camera you want to pair has been Turn off the receiver to which the camera you want to pair is
paired with another receiver. connected and wait a while (30 seconds) before pairing again.
"The button has been pressed for The pairing switch has been pressed Check that there is nothing on top of the pairing switch pressing it
more than 10 seconds." appears for more than 10 seconds down, and then press the pairing switch once to return to the original
screen.
The pairing switch does not respond The pairing switch is not connected Check the pairing switch's connections and connect the button
when pressed correctly correctly.
CAUTION
G Do not connect the power cable (red)
of either the transmitter or the receiver
to the +B line (permanent power
supply) as this may lead to a flat battery.
G Disconnect the negative terminal of the
battery before connecting the cables.
Failure to do so may lead to electric
shock or injury due to short-circuit. It
may also lead
to damage to
the system
Red components
due to
short-circuit.
Measure