Product Description And Specifications; Product Features; Technical Data; Noise/Vibration Information - Bosch GBH 5-40 D Professional Originalbetriebsanleitung

Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Symbols
The following symbols may be important for the operation of
your power tool. Please take note of these symbols and their
meaning. Correctly interpreting the symbols will help you to
operate the power tool more effectively and safely.
Symbols and their meaning
To change the application tool, pull back
the locking sleeve.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for hammer drilling in concrete,
masonry and stone, as well as for chiselling work.
Bosch Power Tools

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Dust protection cap
(2) Locking sleeve
(3) Mode selector switch
(4) On/off switch
(5) Handle (insulated gripping surface)
(6) Speed/impact rate preselection thumbwheel
(7) Auxiliary handle (insulated gripping surface)

Technical Data

Rotary hammer
Article number
Rated power input
Rated speed
Impact rate
Impact energy per stroke ac-
cording to EPTA-Proced-
ure 05:2016
Chisel positions
Tool holder
Lubrication
Max. drilling diameter
– Concrete (with twist drill
bit)
– Concrete (with break-
through drill bit)
– Masonry (with hollow core
bit)
Weight according to EPTA-
Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according
to EN 60745-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 93 dB(A); sound power
level 104 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-6:
Hammer drilling into concrete: a
h
2
Chiselling: a =11.5 m/s , K=1.5 m/s
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
English | 11
GBH 5-40 D
3 611 B69 0..
W 1100
-1
min 170−340
-1
min 1500−2900
J 8.5
12
SDS-max
Central permanent
lubrication
mm 40
mm 55
mm 90
kg 6.8
/ II
2 2
=14 m/s , K=1.5 m/s ,
2
,
1 609 92A 28B | (01.06.2021)