Troubleshooting - Concept OV2010 Bedienungsanleitung

EN
Continuous drainage of water
To use the continuous drainage function, first remove the water tank and
insert a PVC drain hose with a diameter of 10 mm into the drain hole. Then
put the tank back in place.
Make sure that the drain hose is firmly positioned and that no water leaks
anywhere. Connect the drain hose to a suitable water drain. This should be
at a lower level than the water outlet of the dehumidifier. The outlet can also
be connected to a water pump (for example when dehumidifying a cellar).
In the continuous drainage mode, it is necessary to set the desired humidity
to 35 %, the dehumidifier will thus work without interruption.
LAUNDRY DRYING
The dehumidifier can also be used for drying laundry.
Set the desired humidity to 35 % and put the appliance
in Smart mode. Do not place damp clothing directly on
the dehumidifier openings. For best effect, place the
dried laundry 1.5 meters from the dehumidifier.
FILTER CLEANING
Before cleaning the filters, remove the filter cover from the dehumidifier unit.
Air filter
- remove the air filter from the holder
- rinse the air filter under running water
- let it dry and then put it back
Carbon filter
- clean the filter every 2-3 weeks
- carefully vacuum the filter with a vacuum cleaner
- replace the filter with a new one every 6 months for more efficient air cleaning operation
Note: The carbon filter is optional, but never turn on the dehumidifier without the air filter!
Warning:
1. The operating temperature of the dehumidifier is 5-35 °C. Use the appliance within this temperature range. If you
use the device outside the specified temperature range, the safety fuses will stop the operation. This is normal.
2. If the room temperature is below 5 °C, the humidity is relatively low and the dehumidifier cannot be used.
3. The built-in compressor produces heat and it slightly increases the room temperature during operation. This is
normal.
4. The dehumidifier stops operating as soon as the water tank is full.
5. Ensure that the float lever works normally, do not place anything on it.
6. Keep a minimum distance of 20 cm between the openings of the appliance and near objects.
60
TROUBLE SHOOTING
Prior to sending the unit to the service centre, check following points:
Problem
Hot or cold air
comes out of the
dehumidifier.
The unit does not
work.
The dehumidifier
produces no water.
The appliance is very
noisy.
The display shows
an error message E3
or E4.
The display shows
an error message E1
or E2.
The display shows
an error message E5
or E6.
OV2010 OV2010
Cause
When dehumidifying, the appliance
absorbs moist air from the room, which is
This is the normal condition of the
cooled down to reduce humidity.
dehumidifier.
During defrosting, the appliance heats up,
so hot air comes out of it.
The plug is incorrectly connected to the
Check that the plug is properly connected.
socket.
The water tank is full. Empty the water tank.
The dehumidifier is set to a higher humidity
Set the dehumidifier to a lower humidity.
than the one in the room.
The room temperature is too low for Increase the room temperature or change
dehumidification. the location of the dehumidifier.
The appliance is too close to walls or Place the appliance at least 20 cm away
furniture. from any obstacles.
The appliance is not placed on a flat, solid
Place the appliance on a flat, solid surface.
surface.
Clean the filters according to the
The filters are too dirty.
instructions.
Use the humidity reducing appliance only
within its range. Unplug the appliance,
Humidity sensor error and plug it in again after about 5 minutes.
If the problem persists, contact a service
centre.
Do not use the appliance at a temperature
higher or lower than recommended.
Temperature sensor error Unplug the appliance, and plug it in again
after about 5 minutes. If the problem
persists, contact a service centre.
Unplug the appliance, and plug it in again
Abnormal sensor temperature or current after about 5 minutes. If the problem
persists, contact a service centre.
EN
Remedy
61