Werbung
Channel setup
Your receiver has already been preprogrammed at
the factory with the satellite TV channels listed in
the enclosed table (eg. TV channels of the Astra
satellites 1A, 1B, 1C, and 1D) and with the accom-
panying sound channel frequencies. The 10 radio
programme positions R00 to R09 and the 30 favou-
rite channel positions F0 to F29 are also prepro-
grammed at the factory as shown in the table.
Of course, you can also receive channels which are
not preprogrammed in the receiver.
Picture tuning
1
Choose an unused channel position number in
normal mode.
2
Press the
.
key on the remote control handset
twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
3
Press the key
and then the key
.
– This displays the TUNING menu.
6
CHANNEL SETUP
CH 001
11.494 GHZ
POL H
1 TUNING
LNB 1 A
2 NAME / ACCESS
CONTRAST 1
3 AUDIO
VIDEO NORMAL
4 FAVOURITE
EXT DECODER OFF
5 RADIO
I
TERMINATE
OK
STORE
7
4
You can adjust the following basic settings:
(Main) frequency, polarity, LNB input (LNB 1 or 2,
without (A) or with (B) 22 kHz switching voltage),
contrast, and the type of the external decoder.
The current values for these settings are displayed
on the screen.
You can move between each setting with the ]
and | keys.
5
You can alter the settings either with the
and
c
x
keys or, in the case of the main frequency, by direc-
tly entering the value with the numeric keys.
The main frequency and polarity (horizontal/verti-
cal) of a TV programme can be found, for example,
in a satellite TV magazine.
You have the choice of the LNB settings 1 A, 1 B, 2
A, and 2 B.
For details, see the section "Settings/LNB adjust-
ment".
With 1 B (and 2 B), a switching voltage of 22 kHz is
superimposed on the LNB supply voltage (eg. for
controlling a 22 kHz switching relay, or a Multi-
switch).
The receiver's display shows the setting for the
current programme position.
The contrast setting allows the values 0 (factory
default setting), 1, 2 or 3 (custom settings). Pre-
selection of the contrast levels 1 to 3 is described in
the section "External decoder/Preselecting the con-
trast".
For the video type you have the choice betweeen
NORMAL and INVERT. Select the NORMAL setting.
For the decoder, the options OFF, --V (video only),
A-- (audio only), and A-V (video and audio) are pro-
vided.
For the appropriate settings, see the decoder's user
manual or consult your dealer.
O
Press the
key to store the settings.
If the setting OFF is not selected for the current
programme position, the display indicates "EXT:
DECODER" to signal that an external decoder is
required.
Press the
.
key on the handset twice to exit the
menu.
Channel names
The satellite stations given in the attached channel
list have been preprogrammed with the appropriate
settings and channel names.
If you wish to alter the programmed names or give
names to new channels, proceed as follows:
1
1
Select the desired channel position.
2
2
Press the
.
key on the handset twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
3
3
Press the
key and then the
key.
CHANNEL SETUP
EDIT
CHAN 002
1 TUNING
NAME
ZDF–––––
2 NAME / ACCESS
3 AUDIO
ACCESS LOCK NO
4 FAVOURITE
5 RADIO
I
TERMINATE
OK
STORE
4
Move to the first character of the name you wish
to alter/enter with the ] or | key. The selected
4
character will flash.
5
Change the character to the one you require with
5
the
c
and
x
keys.
– These cycle through the numbers 0, 1, ... 9, the +
and – signs, the letters of the alphabet A, B, ... Y,
6
Z and a blank space character.
– A maximum of 8 characters may be used for a
name.
When the name is entered, press the
key to
6
O
7
store.
Press the
key twice to terminate the setting.
7
.
8
9
Sound/radio tuning
When an existing channel changes the sound trans-
mission mode (say, from mono to stereo), you will
need to alter the receiver's audio tuning.
Select the channel position to alter.
Press the
.
key on the handset twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
Press the key
and then the key
again.
– The screen displays the current audio mode with
the sound channel frequencies. The value of the
left channel frequency is flashing.
CHANNEL SETUP
TUNING
CHAN 001
LEFT
7.02 MHZ
1 TUNING
RIGHT
7.20 MHZ
2 NAME / ACCESS
DEEMPH.
GNRS
3 AUDIO
BANDWIDTH
1
4 FAVOURITE
RADIO
OFF
5 RADIO
I
TERMINATE
OK
STORE
Pressing the
c
and
x
keys will cycle through the
23 available positions.
Use the | key to select the RADIO line (ON or OFF
is flashing).
Use the
c
or
x
key to switch the radio mode on
and off.
– In the RADIO ON mode, the picture screen
remains dark.
Press the ] key to return to the audio selection
mode.
When the correct mode is found press
O
to store.
Press the
.
key twice to terminate the setting.
Werbung
