Werbung
General
1
When pressing the
.
key on the remote control
handset once, the channel position, channel name
and time are briefly indicated on the picture screen
of the TV set.
1
2
Press the
.
key on the remote control handset a
second time.
– The MAIN MENU appears.
K 002
ZDF
TIME
20 15
I
MENU
2
3
Press the
,
key when in the menu to display in
A/B
addition the TV picture.
4
Press the
.
key to exit the menu. If you are in a
submenu, you will return to the main menu. When
in the main menu, you will exit this.
Language selection
The receiver offers the following language options
for the menus shown on the screen:
3
Englisch
German
4
French
1
Press the
key on the control handset twice.
.
– The MAIN MENU appears.
5
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
6
2
Press the numeric key
.
– The LANGUAGE menu appears.
7
LANGUAGE
1 ENGLISH
2 DEUTSCH
3 FRANCAIS
I
TERMINATE
3
Press the keys
to
for the desired language.
– This automatically stores the selected language.
The 30 Favourite mode channels for this language
are stored in the channel positions F0 to F29 (see
table of favourite satellite channels).
The clock
The receiver contains a clock which must be set to
the correct day and time when the receiver is first
plugged in or following a power cut. This is neces-
sary to ensure correct operation of the Timer.
Press the
.
key on the remote control handset
twice.
– The MAIN MENU appears.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
Then press key
then key
.
– The CLOCK SET menu appears. The day of the
week and time in hours and minutes are displayed
with the day flashing to indicate it can be altered.
INSTALL MENU
CLOCK SET
1 LNB INSTALL
DAY
MON
2 SET CLOCK
HR
14
3 CUSTOM AUDIO
MIN
00
4 VIDEO
I
TERMINATE
OK
STORE
Use the
or
key to select the correct day of the
x
c
week.
Press the | key to move to the hours.
– The hours start flashing.
Set the correct time (hours) with the
or
key.
x
c
Press the | key to move to the minutes.
– The minutes start flashing.
Set the correct value with the
or
key.
x
c
You can go back to alter your settings with the
] key.
Press the
O
key to store your settings.
Then press the
.
key twice to return to the broad-
cast picture.
LNB Adjustment
You must tune your receiver to match the used
LNB.
Turn on your receiver and select a channel position
with clear reception.
1
Press the
.
key on the remote control handset
twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
2
Now press the key
and then the key
.
– This displays the LNB INSTALL menu.
INSTALL MENU
LNB
GHZ
1 A
09.750
1 LNB INSTALL
1 B
10.000
2 SET CLOCK
2 A
10.000
3 CUSTOM AUDIO
2 B
10.000
4 VIDEO
LNB POWER ON
I
TERMINATE
OK STORE
1
3
Now press the
,
key to see the broadcast
A/B
2
picture behind the menu.
– The LNB install screen displays the LNB local
3
oscillator (LO) frequencies.
These are set to the correct value for a particular
type of LNB but may need to be fine tuned for your
LNB.
4
Use the
or
key to vary the frequency in each
x
c
direction.
!
When the LNB LO is off-tune, black or white speck-
les (sparklies) are produced on the picture.
Adjust the frequency back and forth to give the
least sparklies of either colour or remove all the
sparklies.
5
You can switch to the next or previous menu option
by means of the | or ] key.
6
Repeat this adjustment for the second LNB.
!
If the display indicates RTL 2 when it should show
ZDF, you have the incorrect LNB fitted. This can be
corrected for by altering the LNB LO frequency
from 9.750 to 10.000 by means of the numeric keys
and then fine tuning as before.
Increasing the LNB LO frequency will reduce the
number of white sparklies and decreasing the
frequency eliminates the black sparklies.
How to activate and deactivate the 22 kHz switching
voltage for the respective channel position is ex-
plained in the section "Channel Setup".
Switching on/off the LNB power
Under the menu option "LNB POWER ON/OFF" you
can switch on and off the LNB power by means of
the
or
key.
x
c
LNB
GHZ
1 A
09.750
1 B
10.000
2 A
10.000
2 B
10.000
LNB POWER ON
OK STORE
You must select, for example, "LNB POWER OFF",
for a single cable installation with several receivers
connected.
The factory default setting is "LNB POWER ON".
Store the settings with the
O
key.
Press the
.
key twice to terminate the settings.
It is in addition possible to switch on and off the
power of the two LNBs by means of two switches at
the back of the STE 1000 (see figure).
Use a pointed object (e.g. a ball pen) for actuating
the switches. When switching on the LNB power
again in the menu, the respective switch must be
activated too.
LNB 1
VCR
DECODER
13V / 18V
300mA DC
LNB 2
LNB POWER
2 1
=
Werbung
