Werbung
Normal mode
2
The receiver has also a Normal mode to directly
access every preset channel.
1
Choose the Normal mode by pressing the
¢
key
F
on the remote control handset until the receiver's
display shows just three digits.
2
Use the ] or | key on the handset or the
and
keys on the receiver (behind the front flap) to
3
alter the channel number step by step.
– The number of the channel selected is briefly
displayed on the picture screen along with the
4
channel name.
You can also key in the number directly with the
keys
to
as two or three digits.
Make sure to complete the entry within 2 seconds.
!
3
If you wish to return to the Favourite mode, press
the
¢
key.
F
!
Recording satellite programmes
If your receiver is connected to a video recorder,
you can record satellite programmes.
Starting recording manually
1
Select the desired channel position on the receiver.
2
Select the channel position for the satellite receiver
on the video recorder and start recording.
Programmed recordings
You can programme your receiver so that it
receives up to 8 events within a period of 28 days
and passes these on to your video recorder while
you are not at home.
Of course the timer of your video recorder must be
programmed correspondingly.
Press the
key on the remote control handset
1
.
twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
Press the numeric key
.
– This displays the TIMER menu. The digit behind
"EVENT" is flashing.
EVENT 1
OFF
DAY
HOUR MIN
START MON1 00
00
STOP
00
00
CHAN F05
NTV
TIME
MON 00
00
OK
STORE
You can move through the event timer screen using
the ] and | keys.
You can select the desired data with the
c
and
x
keys.
The setting being altered flashes on the screen.
It is also possible to directly enter the time with the
numeric keys.
If the video recorder is only connected via the aerial
lead with the receiver, you must make the adjust-
ments described on page 8.
Note that it is not possible to record one satellite
TV channel while watching another channel from
satellite. Your receiver can only tune to one channel
at a time.
If you wish to programme a video recorder via VPS,
the satellite receiver should be switched on a little
before and switched off after the broadcast to be
recorded (to be programmed via the Timer). This
makes sure that the broadcast will completely be
recorded even if there should be shifts of the start
and end times. If you wish to make absolutely sure
that the broadcast is completely recorded, the SAT
receiver must be permanently switched on and set
to the desired programme position.
You must enter the following data:
The event number and day of recording.
The number following the day stands for the week
1
(MON 1 = monday first week,
MON 2 = monday second week ...);
the start time in hours and minutes;
the stop time in hours and minutes;
2
the channel position.
5
Once you have set the times and channel for an
3
event, turn the event on by selecting "EVENT" with
the | or ] key and altering the "OFF" at the top of
the screen to "ON" with the
c
or
x
key.
6
Press the
O
key to store the setting.
7
Press the
key twice to exit the menu.
.
The receiver indicates the timer is set by showing
the
symbol in its display.
4
The receiver must be in standby when the event
time arrives. The receiver automatically turns on for
the programmed time.
If the video recorder is connected via the "VCR"
EURO-AV socket, the
symbol is shown in the
display as long as the video recorder is in opera-
tion.
If no further timer is programmed, the
symbol
5
disappears after recording.
It is sensible to set the receiver's event timer to
start a little before and finish a little after the VCR
timer to prevent recording the channel change.
!
The current time and day of the week is displayed in
the Timer menu. If this is not correct it must of
course be reset as shown earlier in this manual or
the timer will not operate at the correct time.
!
If you are using the receiver when the set time
arrives, the timer will be overridden and not start
the recording.
1
2
3
4
External decoder
Connect your external decoder (eg. Premiere) with
a EURO-AV (Scart) lead to the DECODER socket of
the receiver.
Adjust the type of video signal applicable to the
decoder on the receiver.
Press the
.
key on the remote control handset
twice.
– This displays the MAIN MENU.
MAIN MENU
1 TIMER
2 ACCESS CONTROL
3 CHANNEL SETUP
4 INSTALL
5 LANGUAGE
I
TERMINATE
Press the key
and then the key
again.
– This displays the VIDEO screen.
INSTALL MENU
VIDEO
1 LNB INSTALL
DEC VIDEO BASEBAND
2 SET CLOCK
CONTRAST 1 63
3 CUSTOM AUDIO
CONTRAST 2 50
4 VIDEO
CONTRAST 3 53
I
TERMINATE
OK
STORE
Use the
c
or
x
key to select the relevant option for
your decoder (see the decoder's manual or consult
your dealer).
Preselecting the contrast
Frequency modulated satellite signals are trans-
mitted with different video amplitudes. You will
need to set the correct value for optimum picture
contrast.
You can select 3 different preset contrast levels
(adjustment range 0 to 63).
Use the ] and | keys to move to the desired
menu line.
Use the
or
key to alter the contrast setting.
c
x
Press the
O
key to store the setting.
Press the
.
key twice to exit the menu.
In the TUNING menu, you can select the appropri-
ate settings for the received satellite channel (see
section "Channel setup").
Werbung
