Operating Instructions - Electrolux thermaline S90 Installation Und Betriebsanleitung

III . OPERATING INSTRUCTIONS
1. GENERAL
The Pasta Cooker is used for boiling pasta of all types, rice,
noodles, dumplings, vegetables and soups. The desired
temperature can be adjusted between 50 and 100 °C.
The water trough has a capacity of 40 litres and is operated by
a 13 kW output bar burner.
In the front part of the water trough there is a standing surface
for parking and draining off the baskets. Excess water or foam
can run off through a water overflow under the standing
surface.
The water trough is seamlessly integrated into the appliance
cover. Sharply rounded corners and edges facilitate easy
cleaning. All parts of the appliance are made of corrosion-
resistant stainless steel.
Recommended accessories:
- rectangular baskets, 1 x GN 1/1, 2 x GN 1/2 or
3 x GN 1/3
- round baskets, 3
- Base insert to stand round baskets on.
- Cover
2. OPERATION
Turn on main gas tap (1/Fig.10).
In the case of liquid gas operation, also open the bottle or
tank valve.
Turn on the water supply tap (4/Fig.9) until the trough is
full.
Switch on trough heating (Chapters 2.3 and 2.4).
Water loss in the trough can be replaced by turning on the
tap (4/Fig.10).
3
1 Main gas tap
2 Knob
3 Piezo ignition device
Fig.9 Control panel
The knob (2/ Fig.9) has four main settings:
Off
Igniting the pilot burner
High setting
Low setting
Seite 20

OPERATING INSTRUCTIONS

2
1
4 Water supply tap
5 Water drain valve
Fig.10 Front view
2.1 IGNITING THE PILOT BURNER
Push the knob (2/Fig.9) fully in.
Turn it anti-clockwise to the pilot burner ignition (
tion.
Push the knob (2/Fig.9) fully in and hold it there.
At the same time, ignite the gas escaping at the pilot bur-
ner with the piezo ignition device. The burner is ignited by
turning the knob (3) clockwise or anti-clockwise.
After lighting the pilot burner, keep the rotary switch
pushed in for about 15 seconds more.
It is only after this period of time that the pilot light will burn
after the rotary switch is released.
If the pilot light goes out again, repeat the whole process.
2.2 IGNITING THE MAIN BURNER
Press the knob (2/Fig.9) in lightly and turn it anti-clockwise
from the pilot burner ignition position (
setting ( ).
The highest setting ( ) equates to the maximum burner
output or rated thermal load.
2.3 TEMPERATURE SELECTION
The intensity of the flame can be adjusted between the "high
position" ( )and the "low position" ( ).
Push the knob (2/Fig.9) in fully and turn it anti-clockwise
from the highest setting ( ) towards the lowest setting ( ).
The flame thus becomes smaller and smaller.
The main burner has the least output in the low setting ( ).
To return from the low setting ( ) to the high setting ( ),
push the knob (VB, HB / Fig.9) fully in and turn it clockwise.
Note:
Do not switch on the trough heating or leave it switched on, if
the water level falls below the marking on the trough wall. Non-
observance of these instructions can cause severe damage to
the boiling trough and the appliance operating elements.
2.4 OPERATION
Before initial operation of the appliance, the trough and the
baskets must be thoroughly cleaned of the protective indu-
strial grease by carrying out a boiling procedure without
food and with the addition of neutral soap.
2.4.1 STANDBY
The water must always be at the correct level, clean and
always able to be kept at the boil.
4
5
) posi-
) to the highest
62.9680.01