Herunterladen Inhalt Inhalt Diese Seite drucken

Troubleshooting - Scheppach HS720 Originalanleitung

Vorschau ausblenden Andere Handbücher für HS720:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

21. Troubleshooting

Problem
Possible Cause
The saw does not
1. Mechanical brake is defective
brake when switching
the machine off
Saw blade gets loose
1. Fastening nut tightened
after turning off the
insufficiently
motor
Burns on the cutting
1. Bodkin saw blade
surface
2. Wrong saw blade
Engine won't start.
1. Spark plug wire disconnected.
2. No fuel or old fuel.
3. Choke not in the open position.
4. Clogged fuel line.
5. Fouled spark plug.
6. Flooded engine.
7. Low engine oil level
Engine runs irregularly. 1. Loose spark plug wire.
2. Engine running with CHOKE.
3. Clogged fuel line or stale fuel.
4. Blocked ventilation.
5. Water or dirt in fuel system.
6. Dirty air filter.
7. Incorrect carburettor adjustment.
Overheated engine
1. Low engine oil level.
2. Dirty air filter.
3. Air flow restricted.
4. Carburettor not adjusted properly.
Motor does not start.
1. Failure of mains fuse
2. Extension cable defective
3. Connections at the motor or switch
out of order
4. Motor or switch defective
Incorrect motor rota-
1. Capacitor defective
tion direction
2. Incorrect polarity /
Incorrect connection.
Motor does not work,
1. Cross-section of the extension
the fuse responds
cable is not sufficient
2. Overload due to blunt saw blade
Burnt areas on the
1. Blunt saw blade
cutting surface
2. Incorrect saw blade
m Electrotechnical maintenance works should only be carried out by an electronics technician!
32
GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Help
1. Have the brake replaced
1. Tighten fastening nut, right-handed thread
1. Insert a sharpened saw blade
2. Change the saw blade
1. Connect the spark plug wire to the spark plug
securely..
2. Fill with clean, fresh gasoline.
3. The throttle lever must be positioned at cold start at
choke position.
4. Clean the fuel line.
5. Clean, replace or adjust spacing.
6. Wait a few minutes before trying again, but do not
let the engine suck in.
7. The oil guard keeps the oil level low preventing the
engine from starting - Check the oil level.
1. Connect and tighten spark plug wire.
2. Move the choke lever to OFF.
3. Clean the fuel line. Fill the tank with clean, fresh
gasoline.
4. Clean the ventilation.
5. Empty the tank. Fill the tank with fresh fuel.
6. Clean or replace the air filter.
7. Consult the service
1. Fill crankcase with proper oil.
2. Clean the air filter.
3. Remove and clean the case.
4. Consult the service
1. Check the mains fuse.
2. Replace defective extension cable
3. Check with the help of an electrician
4. Check with the help of an electrician
1. Have this checked by an electrician
2. Change direction of rotation with phase inverter /
Have an electrician change the polarity of the wall
plug.
1. Refer to Electrical Connection
2. Replacing the saw blade
1. Sharpen/replace saw blade
2. Replace saw blade

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Diese Anleitung auch für:

Hs720b590510990159051099025905109903

Inhaltsverzeichnis