Technical Data; Before Starting The Equipment; Attachment And Operation - Kity 3401203901 Originalbetriebsanleitung

• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.

6. Technical data

AC motor
Power
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Swivel range
Mitre cut
Saw width at 90°
Saw width at 45°
Saw width at 2 x 45°
(double mitre cut)
Protection class
Weight
Laser class
Wavelength of laser
Laser output
* S6, continuous operation periodic duty.
Identical duty cycles with a period at load fol-
lowed by a period at no load. Running time 10
minutes; duty cycle is 25% of the running time.
The work piece must have a minimum height of
3mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks
can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
220 - 240 V ~ 50Hz
1800 Watt
S6 20%* 2200W
5200 min
-1
ø 216 x ø 30 x 2,8 mm
60
-45° / 0°/ +45°
0° bis 45° nach links
300 x 65 mm
300 x 38 mm
200 x 38 mm
II
approx. 10,5 kg
2
650 nm
< 1 mW
97,7 dB(A)
3 dB
110,7 dB(A)
3 dB
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal per-
formance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op-
erations.

7. Before starting the equipment

• The equipment must be set up where it can stand
securely. Secure the machine on a workbench or a
stand with 4 screws through the holes in the fixed
saw table (18).
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you press the ON/OFF switch check that
the saw blade is fitted correctly. Moving parts must
run smoothly.
• Before you connect the equipment to the power
supply make sure the data on the rating plate are
dentical to the mains data.

8. Attachment and operation

8.1 Attaching the saw (Fig1/2/3/4/5/6/7/8/9)
• In order to adjust the rotary table (17) loosen the set
screw (9) approx. 2 turns, and Press lever (14a) up-
wards.
• Turn the rotary table (17) and pointer (15) to the de-
sired angle measurement on the scale (16), release
lever (14a) and secure with the set screw (9).
• Pressing the machine head (4) lightly downwards and
removing the locking bolt (32) from the motor bracket
at the same time disengages the saw from the low-
est position.
• Swing the machine head (4) up until the release lever
(3) latches into place.
• Attach the table insert extension (14) as shown in fig-
ure (4/5/6). To do so, draw the pin (31) out with one
hand, fasten the extension in the grooves intended for
this (4a) with the other hand, press the lever (14a) up-
wards to facilitate the installation. Release the pin (31)
and lever (14a) and secure with the set screw (13).
GB 23