Kity 3401203901 Originalbetriebsanleitung Seite 22

Maintenance and repair
2
Pull out the mains plug for any adjustment or
–
repair tasks.
The generation of noise is influenced by vari-
–
ous factors, including the characteristics of saw
blades, condition of saw blade and electric tool.
Use saw blades which were designed for re-
duced noise development, insofar as possible.
Maintain the electric tool and tool attachments
regularly and if necessary, initiate repairs in or-
der to reduce noise.
Report faults on the electric tool, protective
–
devices or the tool attachment to the person
responsible for safety as soon as they are dis-
covered.
Safe work
3
- Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
- Never use the machine to cut other materials as
specified.
- To transport the machine follow the procedure
of point 9.
When transporting the electric tool, only use
the transport devices. Never use the protective
devices for handling or transport.
- Operate the machine only if the protective de-
vices are functional, in good condition and in
the correct position.
- The floor around the machine must be level,
clean and free of loose particles, such as chips
and cutting residues.
- Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of the machine and which
are suitable for the material to be cut.
- Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for the
intended purpose.
- Attention! Do not replace the laser by a differ-
ent type.
Repairs may only be carried out by the manu-
facturer or an authorized representative.
- Do not remove any cutting residues or other
parts of workpieces from the cutting zone while
the machine is running and the saw unit is not
at rest.
Instructions for proper and safe sawing:
a) Clamp the workpiece always at the saw table
firmly. Therefore please use the supplied clamp-
ing device.
b) Make sure that the machine is secured before
each sawing;
c) If necessary attach the machine to a workbench
or the like. Fasten the machine to the work-
bench, using the holes at the fixed saw table.
d) Support long workpieces (e.g. with a roller ta-
ble) to prevent them sagging at the end of a cut.
e) Make sure that the saw blade does not
touch the rotary table in any position by pull-
ing out the mains plug and rotating the
22 GB
saw blade by hand in the 45° and 90° posi-
tion. If necessary, readjust the saw head.
Warning! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain con-
ditions. In order to prevent the risk of serious or dead-
ly injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
SAFETY INSTRUCTIONS FOR THE HANDLING OF
SAW BLADES
Only use insertion tools if you have mastered their use.
1
Observe the maximum speed. The maximum
2
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
Observe the motor / saw blade direction of rotation.
3
Do not use any insertion tools with cracks. Sort out
4
cracked insertion tools. Repairs are not permitted.
Clean grease, oil and water off of the clamping
5
surfaces.
Do not use any loose reducing rings or bushes for
6
the reducing of holes on saw blades.
Make sure that fixed reducer rings for securing the
7
insertion tool have the same diameter and have
at least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel to
8
each other.
Handle insertion tool with caution. They are ideally
9
stored in the originally package or special contain-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
Prior to the use of insertion tools, make sure that
10
all protective devices are properly fastened.
Prior to use, make sure that the insertion tool
11
meets the technical requirements of this electric
tool and is properly fastened.
Only use the supplied saw blade for cutting wood,
12
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.