Introduction; Layout; Mains Plug; Scope Of Delivery - Scheppach PLC40 Original Bedienungsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were in-
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety notices contained in this
operating manual and the particular instructions for
your country, the generally recognised technical reg-
ulations for the operation of identical devices must be
complied with.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information..

2. Layout

1. Handle
2. plasma cutter

3. 3 Mains plug

4. Plasma hose package
5. Ground terminal
6. Mains indicator lamp
7. Work light
8. Overheat protection indicator lamp
9. Ground terminal connection socket
9a. Ground terminal plug
10. Plasma burner connection socket
10a. Plasma burner plug
11. Plasma burner power socket
11a. Plasma burner power plug
12. Current controller
13. Plasma burner
14. Plasma burner button
15. Ceramic cap
16. Nozzle
17. Diffuser
18. Electrode
19. Compressed air hose
20. Quick connector compressed air hose
21. Rotary knob to regulate the pressure
22. Manometer
23. Condensation water tank
24. On/off - switch

3. Scope of delivery

A. Plasma cutter(1x)
B. Compressed air hose (1x)
C. Ground cable with terminal (1x)
D. Plasma hose package (1x)
E. Hose clamp (1x)
F. Nozzle (3x) (1x pre-assembled)
G. Electrodes (3x) (1x pre-assembled)
H. Operating instruction (1x)
I. Diffuser (2X)
J. Ceramic cap (2x)

4. Proper use

The machine may only be used in the intended man-
ner. Any use beyond this is improper. The user/opera-
tor, not the manufacturer, is responsible for damages
or injuries of any type resulting from this.
An element of the intended use is also the obser-
vance of the safety instructions, as well as the as-
sembly instructions and operating information in the
operating manual.
GB | 19