Hama EWS-2050 Bedienungsanleitung Seite 5

2. [Clock]
Press once to toggle for clock, calendar & alarm display
mode.
Press and hold 2 seconds to enter the setting of the
display mode – Clock/Calendar/Alarm.
3. [ ]
Press once to increase the setting in clock, calendar or
alarm setting mode or deactivate the radio controlled
function in RCC radio mode.
Press and hold 2 seconds to manually activate the radio
controlled function
4. [ ]
Press once to decrease the setting in clock, calendar or
alarm setting mode.
Press once to arm or disarm the daily alarm under alarm
display mode.
5. [Channel]
Select among channel 1, 2, 3 or to enter auto scroll mode.
Press and hold 2 seconds to activate or deactivate the
sensor searching mode.
6. [Memory]
Toggle for max or min temperature memory reading for
both IN & OUT thermometers.
Press and hold 2s to clear individual memory when the
Max or Min temperatures are displayed.
7. [unit]
Toggle for setting temperature display unit °C or °F.
Press & hold 2s to set the crystal weather icon
illumination cycle.
8. [Reset]
Press once to trigger system reset and restore all setting
to factory default
Slide switch [BACKLIGHT] to select the backlight mode
Slide Battery Only Battery & Adapter only
switch Adapter
position
Auto Wave hand Wave hand
in front of in front of
the IR sensor the IR sensor
to activate to activate
backlight for backlight for
16 seconds 24 seconds
8
00092650bda.indd Abs2:8-Abs2:9 00092650bda.indd Abs2:8-Abs2:9
OFF Disable the
backlight
function
ON Wave hand Backlight
in front of always on
the IR sensor
to activate
backlight for
16 seconds
GETTING STARTED
This Weather Station was designed for easy set up. For
best operation, the following steps are required to be
done in the proper sequence.
1. Insert batteries for main unit before doing so for the
sensor units.
2. Receiving unit cannot be programmed manually until
the wireless remote sensor unit registration
proocedure has been completed.
3. Position the remote unit and main unit within effective
transmission range, which, in usual circumstances, is
75 meters.
Although the remote unit is weather resistant, it should
be placed away from direct sunlight, rain or snow.
BATTERY INSTALLATION FOR MAIN UNIT
1. Turn the metal nut anti-clockwise on the bottom of the
unit to open and release the battery compartment;
2. Insert 4 AA size 1.5V alkaline battery as indicate by the
polarity.
3. Push the battery compartment back, turn the metal nut
clockwise to lock.
Note: Replace the batteries when the low battery indica-
tor appears on the top-right corner of the LCD.
WIRELESS REMOTE SENSOR REGISTRATION
PROCEDURE
1. Insert x4 AA batteries fi rst to the main unit, the
temperature display shows - - . – While the wave icon
will keep blinking for 2 minutes indicate unit is in
sensor searching mode.
2. In a second step, insert the x2 AAA batteries for the
sensor unit. The LED on the front panel will start
fl ashing at a rate of one time per around 2 seconds
indicates channel-1 is in use.
3. While the LED is fl ashing, press once the [CH] key will
change the sensor channel setting to 2. Keep toggle on
[CH] key can change channel setting up to 5. The LED
is blinking at a frequency to indicate the channel
setting. i.e. continuous blinks 2 times indicate channel
2 is selected.
Note: If user does not press any key for 10 seconds, it will
exit the channel setting mode and transmit the RF signal.
The main unit will register the temperature reading.
(If the transmitter has the LCD display, the C/F key will
toggle the temperature unit on the LCD.) As the channel
4 & 5 are reserved for other models, please never set the
remote sensor to channel 4 & 5.
REMOTE CHANNEL AUTO-SCROLLING
This device is equipped with an auto-scroll function.
While the auto-scroll function is set, the unit will
automatically cycle to display the temperature of each
remote sensor for 4 seconds.
1. To retrieve manually the specifi c sensor temperature
reading, press CHANNEL key until desired channel
number is displayed.
2. To enable auto-scroll function, use CHANNEL button to
select channel 1, 2, ... until auto scroll icon appears.
DCF -77 RADIO CONTROLLED CLOCK
The radio-controlled time is calculated by the Cesi-
um Atomic clock of Braunschweig (offi cial clock of
Germany). Then the time is coded and transmitted from
Mainfl ingen - near Frankfurt - via a signal on DCF -77
(77.5 kHz). The transmitting range of the signal is 1500 km,
which means that most of Western and Central Europe
is covered by this signal. Within this range the received
time is completely accurate. Once sensor signal(s) are
received, the wave icon will fl ash to indicate that the
receiving unit starts to receive the DCF radio controlled
time signal.
Radio Controlled wave icon can indicate 4 levels of signal
status:
very weak weak medium strong
Once the time signal is received, the wave icon will stay
on the LCD, and time and calendar will automatically be
updated.
Note: During 10 minutes of time signal reception, all
manual settings will be suspended. If setting is desired,
the user can press [ ] key once to abort the reception.
SET THE CLOCK, CALENDAR & LANGUAGE
1. Press & hold [CLOCK] button for 2 seconds to enter
clock setting mode. Flashing 24 hours will appear.
2. Press [ ] or [ ] button to switch between 12Hr/24Hr
time format, and then press [CLOCK] button to confi rm.
3. The hour digits will fl ash. Use the [ ] button to
increase by one hour or [ ] button to decrease by one
hour to your desired hours. Holding down either button
will change the increment unit rapidly. Press [CLOCK]
button to confi rm.
4. The minute digits will fl ash. Use the [ ] button or [ ]
button to set your desired minutes. Holding down
either button will change the increment unit rapidly.
Press [CLOCK] button to confi rm.
Note: Every change of minute digit will automatically
reset the seconds to zero.
5. The year digit will fl ash and 'Y' icon appears. Press
[ ] or [ ] button to set your desired year. Press
[CLOCK] button to confi rm.
Note: Year range is from 2000 to 2099.
6. 'D' and 'M' icons will fl ash. Press [ ] or [ ] to select
D M (Date Month) or M D (Month Date) format. Press
[CLOCK] button to confi rm.
7. 'Month' digits will fl ash. Press [ ] or [ ] button to set
your desired month. Press [CLOCK] button to confi rm.
Do the same to set Date.
Note: The weekday will be automatically calculated
and displayed for the date set above.
8. 'E' digit will fl ash. Press [ ] or [ ] button to switch 5
languages display of weekday (English/German
French/Spanish/Italian. See table 1). Press [CLOCK]
button to confi rm.
9. 'ON' digit will fl ash. Press [ ] or [ ] button to set the
RCC on or off. Press [CLOCK] button to confi rm.
Note: The RCC is default set to on.
Table 1
18.05.2009 15:22:29 Uhr 18.05.2009 15:22:29 Uhr
9