Installation - KIKKA BOO 4FIX Gebrauchsanweisung

4.8.1 A correctly adjusted harness ensures that the diagonal seat belt section is positioned,and gives your child the optimal protection.4.8.2 The harness must be
adjusted to that there is a space two ngers wide between the harness and your child' s body.
4.8.3 A Correctly adjusted headrest ensures optimal protection for your child in the safety seat:shoulder belts are at the same level as your child' s shoulders
(Figure 18).
4.8.4 Pull the headrest handle, the shoulder straps will be moved together, select correct height and x them in the correct position for the child by releasing the
headrest handle (Figure 19).
4.9 Adjusting the headrest in an instalation that uses the vehicle safety belt. Groups 2 and 3.
4.9.1 A correctly adjusted headrest ensures that the diagonal seat belt section is optimally positioned, and gives your child the optimal protection.
4.9.2 The headrest must be adjusted so that a space equivalent to two ngers remains between the headrest and the child' s shoulders.
4.9.3 Pull the headrest handle to adjust headrest to the correct height, then release the headrest handle.Place the safety seat on the car seat,put the child in
the seat and check the height.
4.9.4 Repeat the process until the correct height is achieved.

5.INSTALLATION

5.1 Group 0+/1(0-18kg) installed in the rearward facing position
5.1.1 Make sure the 5-point harness of the safety seat has been correctly installed (see section 4.1)
5.1.2 Recline the seat fully. Pull the reclining handle forwarder and adjust the angle of recline to position 4 without releasing the handle. Release the handle
when the seat is in the correct position (Figure 20).
5.1.3 Place safety seat in the back seat of the vehicle and contrary to the direction of travel (Figure 21).
5.1.4 Take out the cushion, pass the vehicle seat belt from behind the backrest. Buckle the vehicle seat belt until you hear a click (Figure 22).
5.1.5 Pass the diagonal vehicle seat belt through the blue belt guide hook, tighten up the diagonal vehicle seat belt to make sure it is as tight tting as
possible. Ensure the vehicle seat belt is not twisted or knotted at any point (Figure 23).
5.1.6 Put the cushion back to the original place.
5.1.7 Open the buckle, put the shoulder harness to the sides,then put the child into the safety seat.
5.1.8 Please check if shoulder harness height is equal to your child's shoulder height. Press the adjusting device and pull the shoulder harness to be loose, then press
the headrest handle to adjust the shoulder harness to the suitable position.
5.1.9 Slide the two tongues together into the buckle. The buckle will not work well till you hear „click". Adjust the child restraint belt to make sure the lap belt is well
restrained the child's pelvis .Then tighten the shoulder straps by pulling the adjustable strap at the front of the bottom cushion (Figure 25).
5.1.10 If you want to release your child from the safety seat, press the adjusting device at the front of the bottom, at the same time pull the should straps. Then
press the red button on the buckle, place the shoulder straps at the side and let your child out.
5.2 Group 1(9-18kg) installed in the forward facing position
5.2.1 For group 1 this car seat has 2 modes of installation. Although we advise to use the seat backward facing to the travel direction for an up to 13 kg child, it
is possible to install the seat forward facing, if:
· The size of the vehicle does not allow safeinstallation of the seat backward facing.
· The size of the child exceeds the height percentiles and this causes the child t be incorrectly positioned in the seat.
5.2.2 Place the child seat forward facing on the vehicle seat (in the direction of travel (Figure 25).
5.2.3 Place the diagonal seat belt section through between headrest and backrest. CAUTION! Do not twist the belt (Figure 26).
5.2.4 Place the lap belt section in the light red belt guides. CAUTION! Do not twist the belt.
5.2.5 Bring together about 80cm of the diagonal seat belt section and lap belt section (Figure 27).
5.2.6 Ensure the buckle tongues engage in the vehicle seat buckle,you will hear an audible CLICK (Figure 28).
5.2.7 Using your knee to press the child seat, tighten the vehicle seat belt as follows:First pull on the lower part of the diagonal seat belt section near the vehicle seat
buckle to tighten the lap belt section (Figure 29).
5.3 Group 2/3(15-36kg)installed in the forward facing position Note: Must remove the 5-point safety seat belt and sleeping pad before use this group seat (Figure 30).
5.3.1 Press the adjusting device and pull the harness strap out o the metal connector to unlock it.
5.3.2 Place your child into the safety seat, adjust the height of the headrest according to the height of your child, the upper red belt guide hook on the headrest must
be a bit higher than the shoulder of your child. When adjusting the height, hold backrest by one hand ,pull the headrest handle to adjust headrest to the correct
height.
5.3.3 Place your child into the safety seat and pass the vehicle belts through the bottom of the armrest.
5.3.4 Make sure the lap belt is stretched as low as possible over the child's hips,buckle the vehicle seat belt until you hear a click. The diagonal belt must pass the
middle between child's shoulder and neck (Figure 31).
5.4 Removal of the child seat
CAUTION! Remove the child seat from the vehicle. The child seat must never be transported in the car if it is not properly secured.
5.4.1 Release vehicle seat buckle if securing the child seat.
5.4.2 Remove the child seat from the vehicle.
ENGLISH